Jump to content
SAU Community

Wtb: Engine Crane And Engine Stand

SECURITY

By SECURITY,
in Wanted to Buy

 Share

Recommended Posts

wrxhoon Grand Master

wrxhoon

Posted
Posted
yeah its coming back out mate, im machining the crank and using oversize bearings so it should go back together nice and smooth.

I hope you mean undersize bearings NOT oversize or she will be coming out again ..I hope you know someone that knows what they are doing to do the machining for you ..

SECURITY Grand Master

SECURITY

Posted
  • Author
Posted
I hope you mean undersize bearings NOT oversize or she will be coming out again ..I hope you know someone that knows what they are doing to do the machining for you ..

i mean the next bearing size up which off the top of my head is .25

wrxhoon Grand Master

wrxhoon

Posted
Posted

Depending on the condition of your crank, you can get bearings .08mm undersize ,.012 and .25mm undersize . I would grind the crank as little as possible to get it right . While you are at it get your crank checked for runout . Make sure you do everything correct this time so you dont pull it out again .

If i was you i would bore the block out, new pistons and rings and dont forget to use a new h/gasket too .

Good luck with it and if you havent got an engine carne you can buy them from $195, very domestic but will do the job for you .

Duncan Grand Master

Duncan

Posted
Posted

hey be really careful with a 600kg crane. normally they are 2 tonne rated which is at their shortest length, but when you extend them all the way they are reduced to only 500kg. If the 600kg crane is the same it will only be rated at 150kg at its longest setting which you will need to use.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pogman
      George's R33 GTST build

      By pogman · Posted

      small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
    • DraftySquash
      Help Understand GTT Boost Setup

      By DraftySquash · Posted

      Me coming to check the thread to see if my manual boost controller was set up correct......  
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Ah yes but were you responsible? In the time I've had it (just before Christmas) I spun off the track twice and drove into things twice, so four separate incidents.. in two outings. Luckily I have a full OEM GTR front end to put on which is hopefully not a precursor for further, future, more expensive mistakes to come. It is some consolation that anyone who would want to buy my Altia bar would have to paint it anyway, the guards, too. (if they can get over the asymmetry). Hopefully over the weekend I will disassemble and see how badly things are bent. From what it looks like, the headlight has actually just been pushed back and bent the headlight support (which .. somehow... crushed the guard in). I guess the headlight plastic is strong stuff.
×
×
  • Create New...