Jump to content
SAU Community

Recommended Posts

well obviously i shouldnt have posted this in forced induction but well, i wasnt sure which other one to post it in, it is electrical but its to do with ground components and stuff. any way

Basically what happens is i start the car and drive off. Steering all good, nice and light for a while, then it gets realllllllly heavy (after a random interval, usually 2-5 minutes), like as if i ran out of power steering fluid (which isnt the case) then about 30 seconds later i get the HICAS light. Then i turn the car off and on again and the steering is back to easy light steering after which it goes all heavy, then HICAS light, turn off car etc etc

Anyway its gotta be a electrical issue, right?

Can any one suggest anything, because i cant afford to take it to a mechanic and will drive it with no power steering if need be ;

Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/
Share on other sites

The hicas controller is getting no speed signal. i assume your speedo still works as you havent mentioned it, which means either the sensor on the back of the cluster has spat it, or someone has chopped the speed sensor input to the ecu.

Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2082745
Share on other sites

Yeh the speedo still works. The car was fine for quite a while (been driving it about a month no problems) until the other day it started messing up. But no speed signal = power steering not work? Just that if it was a problem with sensing speed, its unusual that it works randomly and once broken can be fixed by turning car off then on. I read somewhere that perhaps its my power levels on the battery or a alternator insufficiency. Any thoughts on that?

Also, what cluster do you mean?

Edited by r32 gts-turbo
Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2082818
Share on other sites

Hi mate, i got sorta the same problem but mines electrical and i know exactly whats wrong with it. when im driving without too much load on the battery eg during the day all is good and hicas light does not come on unless i got the sysem really pumping or the a/c on in which case the hicas light comes on and the steering goes jerky. At night is the worst with lights on whenever i pump the brakes the hicas light comes on n the steering goes jerky. The problem is the alternator battery power is at 11.5 volts when under load but is at 13 with nothing on so in my case its the alternater causing the hicas issue took a while to figure it out. your case may be different but i hope this helps. If you got a multimeter check your battery voltage with the car running but no lights on etc should be around 13v then turn on your lights, a/c, stereo and it drops to say 11.5 - 12 its your alternator. Also measure the negative from the earth of your car and then the negative from your battery, if theres a difference from when you measure between the + and -terminals of your battery and from when you measure from the + of your battery and the earth of your car instead of the - on your battery then its a earthing issue. Hope that helps good luck

Edited by Hui
Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2084235
Share on other sites

I'm having trouble with my HICAS as well, but it's different again. Well slightly:

It all started yesterday when I changed the drivers side far right brake light. I took it for a short drive and everytime I hit the brakes the HICAS light would come on and I would loose my power steering. This is a big concern as I'm going away this Friday and I don't want problems.

After this short drive I returned home turned the car off for 5minutes and then back on and I've been on two 10minute drives since and it hasn't happened at all. The last drive I went on I put the A/C, highbeams on, pumped up the stereo, put on the demister, wiper blades and the batt didn't go below 12.5volts at all.

It's a sometimes problem that's only happened once and now it's scarying me.

Will I have full steering if it happens again?

Are there any more ideas to why it only happens when I brake?

Can it be disabled by removing a fuse? And would that disable the whole power steering or just the HICAS?

My speedo didn't drop as far as I noticed although I was going very slow and was more concerned about the light and lack of steering so maybe it was the sensor.

I wish the fault happened to a pattern, I hate these sometimes problems.

Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2084610
Share on other sites

thanks hui, gotta get home try this out

Hope i dont have to spend money buying a new hicas or some crap, its definitely electrical

Took it for a drive last night, with no stereo for 15 minutes, thrashing the car, goin slow, turning alot and no probs, so ill get get my alternator checkd out at the store round the corner

Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2085856
Share on other sites

  • 1 month later...
didnt want to remove hicas because, well, if i remove it and put the locking kit, without the HICAS i would have no power steering, right? (being that the hicas seems to control whether my power steering is working or not)

na the power steering works either ways.

Ive completly removed the hicas, and the steering is fine.

steve

Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2227814
Share on other sites

It takes the car a good 5 minutes to realise it has no signal. Mine still throws it up occasionally if i have the car idling in the driveway for too long.

LOL. Mine just did this yesterday !! Had the car for like 6 years and this has never happened and after reading this thread, it happens..... Was on phone while it was warming up and talked for about 8-10mins and then when I went to drive away, the HICAS light came on and no power steering. Turned it off, waited about 2 mins then turned it back on again and all sweet :P

Leson learned, more drivin and less talkin !! :(

Link to comment
https://www.sau.com.au/forums/topic/112983-hicas-hell/#findComment-2234305
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 1000ccs are side feeds but they're not currently installed, had my old factory ones in for leak testing purposes, only decided on them because front facing plenums and good top feed rail kits are out of my budget at the moment, are they really that problematic? Had a set of yellow jackets that lasted me 5 years, no real issues, only replaced them chasing this misfire issue that ended up not being ignition related 😄  
    • Are those 1000cc side feeds? If so, that's part of your problem. I have 1480cc and they idle at stoich on 98RON, and all the way to E85. Also your coil packs.....
    • Update for the sake of closure   Ended up getting the intercooler piping all sorted, new plugs and yellow jacket coils, and she was idling mint until it warmed up while I was bleeding the cooling system. Found the misfire to be localised to cyl 3 by unplugging coilpacks, ran a compression test, that checked out, then decided to get a mate to check if that spark plug was firing out of the motor. Upon cranking it over, with the injectors disconnected, the car actually fired and ran on a couple cylinders and heaps of fuel came out the top of cyl 3 I'd say that injector's either spraying incorrectly or spraying far too much, which is fine as I'm planning on replacing them anyway I'm planning on making about 250kW on flex fuel, and have a set of 1000cc injectors from ozautosport, obviously overkill but I'm planning on building the motor and running more boost further down the line, do you reckon they'd be too big for a smooth idle on 98? Thanks for the replies gents, much appreciated
    • I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
×
×
  • Create New...