Jump to content
SAU Community

Urgent - Need Several Sets Of Wheels And Tyres

BNathanR

By BNathanR,
in Wanted to Buy

 Share

Recommended Posts

BNathanR Apprentice

BNathanR

Posted
Posted

Hey guys,

I need the following - if anyone has these it will be something of a miracle, but never hurts to try. Please PM me your offers. Will take decent offers straight away and will arrange freight at my own cost;

Set of 4 235 or 245 16" tyres to suit 8" rims - must be at least 70% tread.

Set of 4 WHEELS AND TYRES TO SUIT Mazda MX5 - must be 17's or 18's.

2 x 18" Abflug Gran Revolfes - I have two of these ( new) already, and need the other pair. Don't really mind width or offset, as I can fit to various cars and use spacers if and where appropriate. The ones I have now are 9J +20, so I suppose anything from 8J through to 11J is fine. Photo attached.

1 x 17" Manaray Sports Hyper R rim. think it's between 7.5J and 8.5J. not sure on offset, let me know if you have one and we can go from there. will attach photo over the weekend. if you have one you know what it is.

1 x 17" x 8J Works Equip alloy. Must be 8J with +30 offset.

Cheers,

Nathan

post-27522-1144905799.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      AC Compressor

      By GTSBoy · Posted

      You don't need an AC mechanic to fit it. You do need one to vac the system down and fill it. That's how you get refrigerant.
    • GTSBoy
      Anti Squat Kit

      By GTSBoy · Posted

      Well, it's actually probably worse than you think. I think you have to (minimally) install GKTech's spherical bush replacements to the lower arm's inner ends, because you absolutely cannot subject the original (or poly) bushes to that much misalignment. The better option being to replace the whole lower arm with GKTech's unit. This brings sphericals to the lower inners either way you do it. And are you aware that the kit is weld in and you have to take the subframe out of the car to get it fitted? It's a fair bit of work. These issues both drive my ongoing dithering about doing this to my car, for the last couple of years.
    • kevboost7
      AC Compressor

      By kevboost7 · Posted

      The website said you need a AC technican to swap it in. Is that true? How did you fill the refridgerant? Was it easy to install?  If i just got the bracket and the new smaller AC compressor, would the other components be compatible with R134?
    • ianp
      Anti Squat Kit

      By ianp · Posted

      Hi All Finally getting back to work on the R32 this weekend and had a quick question about the GKTech anti squat kit (https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=39&_fid=eb6b5077e&_ss=c) So, this straightens out the rear LCA and increases the roll centre by 20MM which is great BUT I also have MFR roll centre adjusters (https://www.rhdjapan.com/moonface-super-lap-rc-joint-roll-center-adjuster-bnr32-ps13-rps13.html) which gives a +15MM lift. My question is whether they can/should be used together or if its going to massively effect the geometry? In my mind, I can't see that they work together but was hoping for some feedback on someone who has done this before deciding which to use or if both?   Thanks
    • TurboTapin
      Rb25 into r31/wont idle

      By TurboTapin · Posted

      Agreed. Thing has to be running absolutely pig rich as well. I would worry a lot less about your idle and start going through all your electrical before the car burns down. 
×
×
  • Create New...