Jump to content
SAU Community

For sale R32 GT-R Mine's computer

Toshi
 Share

Recommended Posts

Toshi Proficient

Toshi

Posted
Posted

Mine's computer is very famous in Japan. It's a plug and play computer. New retail price over A$3000

It's from standard`modfied , eg after market intercooler, exhust front pipe ,muffler,air filter ,boost cotroller, boost 1.0kg or 14psi.

Please give me any offer.

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/11359-for-sale-r32-gt-r-mines-computer/
Share on other sites
Toshi Proficient

Toshi

Posted
  • Author
Posted

It's for R32. R32 and R33 different turbo.

If you know good work shop , It's not problem for PFC.

MIN'S computer is best dater in chip for R32.

If you don't know good work shop , sometime MIN'S computer is better than PFC.

Any computor can chang chip. But not selling in Australia.

How much cost for adjust the PFC?

MIN'S is just plug in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      I removed the IACV, cleaned it and reinstalled.  I found a video on youtube that helped with the whole process, the guy then said the idle needed to be set, so the process was to get the vehicle up to operating temperature, unplug the TPS, set the idle screw in the IACV so the RPMs were around 600, then plug the TPS back in.  After I reinstalled the IACV, the car started (because, it was a cold start), once it warmed up, the car died, I adjusted the idle screw to see if that helped anything, it did not, I had to wait about 3-5 minutes, then the car would start back up. Only to shortly cut out, and only crank.  I loosened the TPS to see if adjusting that would do anything, and when I would rotate the sensor clockwise, there was a humming noise, but it would go away when I got the sensor in the horizontal position.  It only made the hum noise with the key on.  What do you guys think? 20250414_172604.mp4
    • Milkmun
      Magnetic Drain Plug Snapped in Half

      By Milkmun · Posted

      At least it was the ex.
    • Murray_Calavera
      Troubleshooting - motor wont turn over

      By Murray_Calavera · Posted

      Quick update.  The engine grounding strap was replaced, the engine is now happily running.  Tested the voltage drop before replacing the strap, was about 1.2ish volts down between engine to battery, chassis to battery. With the new grounding strap, pretty much no voltage drop at all. 
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I was chatting with an ex SAU person who is involved in chooning euros now. He was saying the factory cars like Audi VW etc have something like 2000 tables that the ECU uses for getting everything "just right". Compare that back to any aftermarket ECU, and you'd be hard pressed to surpass 50 lookup tables. Even the Ford Barra engine has a few hundred lookup tables to run it (and they're still working some tables out too!)
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Grab a temp probe, and probe each exhaust inlet runner with it sitting idling. Each one should be pretty darn close to the same temp. If you've got some reading higher or lower than the others, it's likely either air flow isn't equal, or your injectors aren't equal to each other.   The other things to check, is from the wiring changes that were made, were any earth's or grounds moved/changed.   Lastly, for the strut brace issue. It's not perfect, but can you get away with slipping a washer or two under the strut brace to raise it, and it still clean the bonnet? If you can, work out the height you need, that the motor can't torque up into, and get a spacer made for each side.
×
×
  • Create New...