Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

I've had the same thing a few times recently, co-inciding with a cold snap of weather. Since i'm doing the clutch now, the box oil will be replaced with Redline lightweight shockproof at the same time, which i hope will help. If you're not already running a fully synthetic 75W-90 or shockproof in your box, it might be worth trying that out first. Synthetics perform much better at lower temperatures than minerals, and its a much cheaper option than pulling the box...

Kot.

  • 2 weeks later...

this has happend to me aswell it wouldnt go into gear even if the car was on or off. i tried everything and still no good. so i changed oils to see if it was the problem and it was. in my case the thiner the oil the better it got. so fully synthetic oil is the best way to go. if ur not sure and dont want to spend the money for it. test auto transmission oil the red stuff (not Recommended to drive with just to test if it goes in gear smooth then dump oil and get fully synthetic)

I had a similar problem with my gearbox...driving along and then got jammed in neutral in the middle of a gearchange. After a while (10 minutes or so) of trying it was ok again until the next day then it did the same thing. Unlike the problem JETR-32 had, I could work the gears fine with the car off...because the problem ended up in the clutch. Was caused by a busted spring from the centre plate of the clutch which stopped it from engaging to allow the gear change.

yeh someonestolecc i read ur post i think,

was getting another box ya only option?

how about gettin ya selector replaced/fixed?

anyone know the cost of getting that done????

For me it was. I don't know what it's called but the part in the box that sits around the axle thingy, it had actually been sheared off. I think because it was rubbing too hard so probably out of abuse from the previous owner in the form of not maintaining it properly.

I dono what it's called lol BHDave will know he took it out :D:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...