Jump to content
SAU Community

Screeeeeching Starter Motor? But It Still Works!

superspit

By superspit,
in General Maintenance

 Share

Recommended Posts

superspit Mentor

superspit

Posted
Posted (edited)

Hi 'liner's, been a while, hows it all...............er.....anyways! (Guess that means my line is going ace!)

After doing a little searching/reading of our wonderful forumns, I have determined that it is my starter motor making some wonderful, pre-historic bird type noises, after successful ignition (screeching noise lasts for upto 1-2 seconds after she starts).

At first, I thought it was fan belts, now I believe it's the starter(?). (tightened belts, lubricated them just to check, cleaned up afterwoulds).....noise still exactly the same.

So, 3 questions/queries........

A) Would u concur with my comments thus far, that it looks like the starter may not be 'recoiling' back?

B) I imagine, by looking at this part of the car, that removal of the starter would best be done from under the car(?).....Would u agree? (1995 series 1.5 R33 GTS-t)

C) I plan on removing the starter and cleaning it majorly (strip it as best I can) and lube it. (Worth doing?....any problems foreseen by you people?).

Hey Guys....thankyou in anticipation.

Maybe someone knows the price of install/part too......justin'

Up the 'irons!!

Mark, Superspit.

DON'T BOTHER, NOW TAKING TO MECHANIC!!!!!!

Edited by superspit
superspit Mentor

superspit

Posted
  • Author
Posted
Its because the gear in the starter motor is not being pulled back after you release the ignition key. Probably needs a fresh grease - if not buy a re-co starter motor.

ta MR33....yeah, that's the same tact I'm taking....so far. What do you reckon guys?

superspit Mentor

superspit

Posted
  • Author
Posted
yup my 33 just started doing that... Exactly the same noise as you are describing.. im planning on removing mine and giving it a nice grease up

there you go!....thanx man.

Do you know what ur up for.....work wise? Will u be going in from down under, or from above.

Any info u know about actual removal would be further appreciated!

Mark.

Ruffels Veteran

Ruffels

Posted
Posted

hmmm i havent looked into it too much as i dont drive the car anymore... im just getting it ready for sale... however i had a quick look the other day.. starter motors only usually have 2 bolts holding them in.. bit tricky coz its on the side of the bell housing .. running next to the gearbox

im fairly sure only way to do it is from below!

i'll give it a crack and let you know how i go

shouldnt be too hard.. i replaced the starter motor on my old rwd 626 lol

-Ruffels

jap33 Explorer

jap33

Posted
Posted

dude my car done exactly the same, all i did was take out the started motor and found that the gear on the shaft was not lubricated and had minimal play. all i did was put some grease on the shaft, hooked it up to a battery let it go off a few times and WALLAH.....

superspit Mentor

superspit

Posted
  • Author
Posted
dude my car done exactly the same, all i did was take out the started motor and found that the gear on the shaft was not lubricated and had minimal play. all i did was put some grease on the shaft, hooked it up to a battery let it go off a few times and WALLAH.....

Dooooooooode! This sounds very 'heartening'.....I'm giving it a bash over this weekend.

Got my chassis stands and 13-14 mm socket/spanner etc.....can't wait to see if mine fixes like yours!!

Thanx Dooooooooooode. :(

Mark.

  • 1 month later...
chopobo Veteran

chopobo

Posted
Posted

any idea on which parts of the starter do you lube up?

and how much grease you should apply?

im assuming its that big copper thing that pops out?

or the magnet things inside the motor?

im seriously clueless into what needs to be lubricated?

can anyone give me advice

jakegts Rising Star

jakegts

Posted
Posted (edited)

Had the same noise, starter gear was stuck in "mesh"...

Had the whole thing reconditioned and now works perfectly... total cost was around $250..

not sure if i got ripped off but that how much i payed for it...

Edited by jakegts
superspit Mentor

superspit

Posted
  • Author
Posted
BUMP! SORRY!

DON'T BOTHER, NOW TAKING TO MECHANIC!!!!!!

$115.50 ..............fantastic,,,,,,,,,,,,couldn't do it cheaper myself, and not get frustrated and break something else!

My honest mechanic Pulled unit out, cleaned out 11 years of crap, lubricated all moving parts, bench tested, re-installed.

That's it! Like new now.

Unless you're tooled up..(and I thought I was)............don't bother doing this yourself!!

Zenith Contributor

Zenith

Posted
Posted

Good that you got it fixed and cheaply too.

I managed to remove a starter motor from a FWD pulsar, the starter motor is under the inlet manifold, and to get to it, all the inlet piping before the throttle butterful had to be removed to get to the botls. Then the car had to be jacked up and remove starter motor from underneath. I found it too be the bushes had worn right out and were scraping on the commutator, so it was still starting with lots of screeching. The bushes on the starter motor usally last around 90k - 100k Kms.

I would think that starter motor from a RWD car would be much easier to remove being on the side of the bellhousing in the trans tunnel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • weikleenget
      R32 GTR clutch master cylinder adapters

      By weikleenget · Posted

      I replaced the whole clutch line with the chase bays braided hose, I think it removes that loop, is it the short hose that comes immediately off the slave or is there a drawing in the manual to find what you’re referring to? It was just re-bled when I upgraded to the nismo slave, old slave worked fine but I thought that might help, didn’t change a thing. It’s like the first half of the pedal is pushing air and then when it finally actuates the master the friction zone is tiny. Makes it practically impossible to launch the car
    • Kinkstaah
      MLR's Bogan cruise ship

      By Kinkstaah · Posted

      Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
    • sonicii
      Mechanic in Victoria

      By sonicii · Posted

      I would agree, unless you need something specific to the HV motor/battery side repaired or investigated, any mechanic will be able to perform normal services, but if you prefer, maybe look for a mechanic who regularly services/repairs Nissans, the VQ engines are pretty common in the Nissan lineup.  Sorry, I can't make any suggestions, I don't live in Vic.
×
×
  • Create New...