Jump to content
SAU Community

Sticky Gearbox

tdr
 Share

Recommended Posts

tdr Contributor

tdr

Posted
Posted

hey guys,

i have just bought an r32 gtr skyline, and i gotta say it is an awesome car.

I have one problem with it at the moment and i was hoping you

could give me some ideas on it.

When i drive the car with alot of traffic, the gears become harder and harder to

get into gear without it crunching. If the car is just crusing it is all fine,

but in traffic it gets really notchy.

Now the clutch has been replaced and it engages really far down, as in you

lift your foot approx 1cm and the clutch disengages.

So what do you guys think it is?

could it be the gearbox fluid, or the clutch adjustment.

Any help would be great,

thanks

Todd

Link to comment
https://www.sau.com.au/forums/topic/114171-sticky-gearbox/
Share on other sites
danielson Proficient

danielson

Posted
Posted
hey guys,

i have just bought an r32 gtr skyline, and i gotta say it is an awesome car.

I have one problem with it at the moment and i was hoping you

could give me some ideas on it.

When i drive the car with alot of traffic, the gears become harder and harder to

get into gear without it crunching. If the car is just crusing it is all fine,

but in traffic it gets really notchy.

Now the clutch has been replaced and it engages really far down, as in you

lift your foot approx 1cm and the clutch disengages.

So what do you guys think it is?

could it be the gearbox fluid, or the clutch adjustment.

Any help would be great,

thanks

Todd

could be a lot of things.. my r33 gtst 5speed box was doin a similar thing, i thought lack of oil. i drained it and changed it, it had heaps of oil.. but more metal than oil came out!!! after i cleaned the metal shevings out, it seemed to stop

Link to comment
https://www.sau.com.au/forums/topic/114171-sticky-gearbox/#findComment-2103157
Share on other sites
GTR32GUS Mentor

GTR32GUS

Posted
Posted

My gearbox was abit notchy when I got my gtr , changed the oil on the weekend to redline lightweight and it like somebody put in a new gearbox in , great stuff , thank to all the ppl on here who advised to use this stuff

Do a oil change c what happens , u will need a good 1/2in bar as the drain bolts are tight as

Link to comment
https://www.sau.com.au/forums/topic/114171-sticky-gearbox/#findComment-2103857
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...