Jump to content
SAU Community

Overheating With Aftermarket Rad And Fan

SkylineBNR32
 Share

Recommended Posts

SkylineBNR32 Rookie

SkylineBNR32

Posted
Posted

I'm having a little problem with the engine on my GT-R overheating. If I let it sit and idle in even mild (18-20 degrees celsius) temperature, the coolant temp almost goes through the roof and my oil temp climbs up to 110 degrees c. The current setup is a Koyo 2 row aluminum rad measuring 26" x 18" x 2 1/4" and the fan is an electrically controlled 14" fan which is much smaller both in diameter and blade size to the stock fan. However, the rad is twice as big. Would the extra coolant not keep the motor cool? If not, what fan should I find to fix this overheating problem. I think I have figured out the oil temp problem, being that I put in 0w40 synthetic which I had a bad feeling about anyway. Im changing it out after just about 200 km to 10w40 synthetic because I don't trust that lighter oil. Could the overheating also be cause in part by the lighter oil? Is it possible that I have already damaged my turbos by running the lighter oil? By the way, the motor is stock with the factory boost restrictor removed and HKS pod filters and a 3-inch Apex'i cat back exhaust. Also, I am getting a stumble on accleration after 5500 RPM. Does the factory ECU actually retard the performance so much as to get a bad miss and very rich conditions? Any help would be appreciated because I am not experienced enough with cars to figure this out without expert advice.

Link to comment
Share on other sites
sh@un Grand Master

sh@un

Posted
Posted

Now I assume you do realise that the water-pump is driven off the same pulley that the factory viscous/thermatic fan is mounted to, yes?

If this isn't being driven, you have no coolant flow. If it is being driven, is it slipping badly? That could cause the water in the block to have too low a pressure. Both these would cause high oil temps, too.

110deg C oil temps at idle are ridiculously high.

Part-time electric thermo fans are garbage for hi-po engines like RB26's, the engine bay should have a constant supply of fan driven air to keep heat-soak down. Plus the mechanical fan pulls air through the intercooler.

And finally- always use a radiator fan shrould. The radiator won't be as efficient without one.

Hope this helps.

Link to comment
Share on other sites
BHDave Grand Master

BHDave

Posted
Posted

Did you buy the car with the current radiator setup on it, or have recently swapped it and the overheating issue has started since the swap.

Does it overheat when driving on the freeway or at a reasonably constant speed?

If it doesn't cook when driving there are a couple of quick things to check,

1) that the fan has the blades around the right way to pull the air through the core (or push if you have it on the front)

2) That the factory thermo mounted to the front is still working (it should kick in at about 90 degrees).

I suspect that it is an airflow issue and the single 14 can't pull enough air through the core as it's a pretty thick unit

On a general maintenence front, it's worth checking that the thermostat isn't stuck shut if it overheats no matter what and also run a flush through the system to clean out any scale and shit from the block.

Link to comment
Share on other sites
Abo Bob Grand Master

Abo Bob

Posted
Posted

How quickly does this happen? I suspect the thermostat if it happens quickly.

A 14" fan will not pull enough air through even if it's working properly but on cool days driving along it should still be fine. I think some of them can be wired backwards which can spin the fan in the wrong direction.

Stock fan or 16" thermo, stock is better.

Link to comment
Share on other sites
SkylineBNR32 Rookie

SkylineBNR32

Posted
  • Author
Posted

Thanks for the comments. My first thought was that the stock fan would be much better as it is about twice the size of this electric fan, which is definitely a piece of junk, the problem with the stock fan is that when the engine is reved the blades bend forward and smashed the crap out of the rad before. had to get a new one ordered in, however it was installed at a body shop and not by me. is there a stock sized fan that would not bend like this that I could mount on the water pump pulley?

Link to comment
Share on other sites
SkylineBNR32 Rookie

SkylineBNR32

Posted
  • Author
Posted

I have one more question. Where is the connector for the outside temperature sensor located? The manual says to disconnect this sensor with ignition on to force the Auto A/C into heat mode but the picture in the book really sucks and I can't figure out where this connector is located.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      GReddy Injector Help!

      By Duncan · Posted

      Ultimately, if the tip is not far into the runner and the o-ring seals, then you are in business. Have you applied pressure to it as is? It is not really a problem for the injector to twist once it is bolted down, the oring seals it and you don't want it jambed into the oring too hard The plenum is intended to take multiple size lower injectors with different adapters, but the way you have it is fine if they seal.
    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • GTSBoy
      Compatible rear drive shafts R34 N/A?

      By GTSBoy · Posted

      They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
×
×
  • Create New...