Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

so what should i do, i'v taken the car back numerous times and it's always the same result, all that happens when i take it back is the tuner just keeps lowering the timing, to me it seems like he just can't be bothered

I might as well get the stock ecu put back in, cause thats what it feels like

Edited by Hulk1010
It really depends where it is knocking.

If it's on over run then not a major concern, or if you are bouncing off the limiter then it isn't uncommon as the pfc cuts fuel creating a lean condition

Fuel cuts aren't a lean condition as all the injectors are shut off. Knocking on the rev limiter is usually from crackshaft harmonics due to the massive rotational decelleration. Find out when the knock occurs and we might be able to help you out more.

Edited by rob82

thanks for the replys

I'ts always before the limiter, at random times, I might give it a boot from 2nd, 3rd, 4th etc and end up getting a high reading, could it be the knock sensor?

a week back i gave it a boot from second and then checked the knock level reading and it read 111, the RPM was 5500

thanks for the replys

I'ts always before the limiter, at random times, I might give it a boot from 2nd, 3rd, 4th etc and end up getting a high reading, could it be the knock sensor?

a week back i gave it a boot from second and then checked the knock level reading and it read 111, the RPM was 5500

By that knock level you should actually start to hear it through the fire wall. Is it a temperature based problem ie does it do it at night on the highway or slow cruising around town in the heat of the day?? If you pull 2 deg out globally does it stll do it??

By that knock level you should actually start to hear it through the fire wall. Is it a temperature based problem ie does it do it at night on the highway or slow cruising around town in the heat of the day?? If you pull 2 deg out globally does it stll do it??

OK - I kind of have this problem too – but not as bad

I have an R32 GTR with Weisco forged pistons - and my knock reading creeps up to the high 50s from time to time. I have also seen bursts up into the 70s but only if I'm using bad fuel.

I have had my engine checked by 3 different tuners - all using head phones to listen for knock - and they all confirm that my engine is NOT knocking

Under the settings menu on your PFC you add advance / retard timing and increase the injector duty cycle across the entire rev range – or 'globally'

I tried taking timing out in steps. I stepped up from -2 / -4 / -8 degrees - and it made no difference to the readings.

I then added more fuel 'globally' - still no difference

I then did some tweaking to both at the same time – still got the same readings (shrugs)

So - I figure I either have a dodgy knock sensor - or just a noisy engine :)

or possibly both

The knock reading can be misleading as ive seen many cars with high readings with no det at all.One GTS read a count of 93 no matter what you did, we even backed the CAS off asd far as it could go and retarded timing with the PFC with no change,even changing the knock sensors did nothing.Use the reading as a guide only but its no where near perfect so us other means as a back up if your not sure.

A maximum power tune will give readings in the 50s also,this is why i like to use other tools for det detection on the dyno on hi powered cars.

Does it do it all the the time?

Every now and then I'll get really high readings,spoke to the tuner and he mentioned it could be the fuel pump.

I've just replaced it and its still playing funny buggers, highest knock of 120 when overtaking in fifth gear with less than 3 qtr throttle.

All other times sits on mid to low 30's!

same boat **raises hand.

Mine has hit a max of 84, but after a bit of driving in low and high revs the knocking is down to lower than ~30. Is this a problem at all?. If I am driving with no hard boosting the knocking is lower than 20....

Also have been told to watch for blowing smoke.

White = water

Brownish = fuel

Black = oil

is that right?

I've put about 6,000km on my GTR in the past 4mths driving in conditions from 5c-44c on 0.8-1.4bar and never have I seen my knock level go above 32.

Maybe it is time for you to find a different tuner Hulk.

I have the same problem with my gtstr33. it spikes upwards of 120 with the aircon on, and up around 50-60 with aircon off. It happens at around 4500-5000 rpm.

I have my map locked so i cant take out any timing to do some fault finding. This is quite annoying seeing the engine check light flash rapidly at me. I hate the thought of slowly killing my engine.

I had mine tuned at one of the best tuners in sydney and it was not detonating on the dyno. I even took it back for them to play with and they did take some timing out. I am wondering if its possible for the car to be using different load points under wot on the dyno to wot on the road. In this case that part of the map may not be tuned????

Does any one else notice a rise in knock if the aircon is on???

^ The engine is working harder with the aircon on... so its gonna show up.

Take it back to this "one of the best tuners" and tell them its still happening. Sacrafice a little bit of power for the overall health of your engine...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • hello! does anyone have a schematic that shows how to test the blower motor resistor for the vac system? i believe the part# is 27761-15U00. I think the resistor is toast, but would like to be able to test it somehow before i embark on the journey to find a new one. cheers! 27761-15U00
    • I don't know the answer to this, but did you have a look at the parts diagrams on amayama.com and see what they list around it for your car? As an example this should be it on my car. That's how I would check for required clips and things like that. But, I take no responsibility for you ending up with a box full of random OEM hoses, washers and clips after going down that path a few times. This definitely has never happened to me  
    • Most driving should* be done on one side of single lane divided roads. In the RHD world, you drive on the left side of the dividing line and the road is probably cambered equally on both sides. So your side of the road slopes away to the left. The same is true for the LHD world, just everything swapped to the other side and opposite slope. With a perfectly neutral, straight ahead wheel alignment designed to drive straight on a perfectly flat surface (or at least one that is level on the left-right axis, even if it has some slope in the fore-aft axis) you will not be able to drive on a cambered road without the car wanting to drift down the camber. You will need to add steering input in the opposite direction all the time. This is annoying. The solution has always been to set the camber and/or the caster to produce a continuous turning force in the opposite direction of the camber. The car will drive straight on the kind of camber for which it was set up, presumably as described in the top paragraph. But.... when the car is set up this way, as soon as you get into a lane, usually on a multi-lane surface road or highway, where the camber is not as presumed during setup, the car will usually pull to one side. In the RHD world, if you are in the fast lane on a big divided road, you are probably on the opposite camber compared to what the car was set up for (ie, sloping down to the right) and the combination of the setup and that camber will make the car want to go right pretty hard. Even a perfectly flat lane will tend to want to go right. There's no getting around it. Civil engineers who know their stuff (which is not an assumption that can always be made) will attempt to keep the variation in camber across a multi-lane road as small as possible, and if they can will attempt to make the fast lane as close to flat, or even cambered in the same direction as all the other lanes. This takes a lot of planning for drainage, control of levels, ability to deal with the elevation changes that occur at road junctions, etc etc. So it's not trivial to get it right. When they do make it work, then the annoyance is reduced, along with tyre wear, fuel consumption, etc. In theory, the civil engineers are supposed to worry about those aspects of road design also. * This used to be true, but now with very large highway systems, even just multi-lane surface roads running everywhere, it is less true now than it was, but the old assumption is the basis for describing the phenomenon, so let's just run with it for the moment.
    • I think the consensus was that's normal. Sloped road surfaces or something? I remember @silviaz went through this before. It might be one of those things you never notice until you pay attention to it.
    • Im not entirely sure exactly what or where its leaking from, he started to pull the boots to swap to my new tie rods + ends and it just vomited fluid, so he closed em up up, swapped the rod ends to the old rods and let me know so I can figure a solution out, im guessing its all origional as as I passed 103k miles earlier this year im sure its just in need of a full overhual/rebuild anyways.    If i could just yank it off and be good it wouldn't be an issue to ship it out and wait for the turnaround but the guy I work with doesnt really have space to keep my car for a week or two at a time, would rather drop it off and have a replacement ready to drop in
×
×
  • Create New...