Jump to content
SAU Community

Recommended Posts

I find this hard to believe ......... over 20 have viewed this thread and NOTHING, not any response.

Where are all the audio god's that know all there is to know?

I want to put 6 x 9's in the back but I'm not prepared to put just anything in.

Doesn't anyone know anything about the best combination or construction of auto audio speakers today, or do we just believe the guy on the other side of the counter that's trying to sell them to you.

I'm not 20 anymore and don't really need to blow my brains out with sound, but do like to listen to some music loud.

I am trying to avoid subs and I'm limiting my power output to 45 WRMS per channel.

I have Pioneer TS-C1002 4" splits for the front (rated at 50 W Nominal) and wanted to use either Pioneer TS-A6971E or Kenwood KFC-M6935A 6 x 9's. Both rated at 70/80W nominal.

Both have very similar specs, 25Hz - 30000, 93db @ 1W/me, 4ohm, but the Kewood's have larger ferrite magnets and a much larger mid range.

Hence my original question.

Cheers, D

pioneer is a better build quality so they might (emphasis on might) be the same

but kenwood are getting better so.....

give the kenwoods a go

bigger midrange cone will give more clarity, while allowing some bass from teh cone area of the actual 6*9

THanks,

As some know I have an older than most model Skyline and really don't want to start hacking up the door trims to fit bigger speakers than can go into the dash relatively easily.

4" splits in the front don't pose much trouble, as the tweeter can go in the cover piece under the dash, but the rear shelf does have a few issues. 5.25 is the largest that will go on the rear deck without spacers, so I made spacers that can accommodate 6 x 9's.

Hence why I ask the question.

Cheers, D

I have read a lot of theory and done a lot of experimentation regarding this subject and as a result you are better off using a 2 way system to reduce the difference in sounds from crossover points and different speakers. I have seen pictures of some massive horn structures to give single 4" speakers enough bass to act as a full range speaker :(

get some good 6" coax speakers instead.

6x9s are sucky and arent really that good.

get some good 6" front splits

some good 6" rear coax's

then a sub or two.

youll never regret it

lol. sif.

if you want good sq and a bit of bass but dont wanna be running subs a decent set of 6x9's in the rear ( i use pioneers ) and some 6inchers in the doors is the best option.

lol. sif.

if you want good sq and a bit of bass but dont wanna be running subs a decent set of 6x9's in the rear ( i use pioneers ) and some 6inchers in the doors is the best option.

OK! Best option opinion please.

TS-A6971E or TS-D691S or R???

Cheers, D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
    • You're probably right about that one. Thanks for your suggestions, I hope I don't need a new 3rd brake light. Although wiring issues might arguably be worse. Right now I'm in the midst of a turbo removal because of my oil leak, other problems are going to have to wait for now.
×
×
  • Create New...