Jump to content
SAU Community

Recommended Posts

I find this hard to believe ......... over 20 have viewed this thread and NOTHING, not any response.

Where are all the audio god's that know all there is to know?

I want to put 6 x 9's in the back but I'm not prepared to put just anything in.

Doesn't anyone know anything about the best combination or construction of auto audio speakers today, or do we just believe the guy on the other side of the counter that's trying to sell them to you.

I'm not 20 anymore and don't really need to blow my brains out with sound, but do like to listen to some music loud.

I am trying to avoid subs and I'm limiting my power output to 45 WRMS per channel.

I have Pioneer TS-C1002 4" splits for the front (rated at 50 W Nominal) and wanted to use either Pioneer TS-A6971E or Kenwood KFC-M6935A 6 x 9's. Both rated at 70/80W nominal.

Both have very similar specs, 25Hz - 30000, 93db @ 1W/me, 4ohm, but the Kewood's have larger ferrite magnets and a much larger mid range.

Hence my original question.

Cheers, D

pioneer is a better build quality so they might (emphasis on might) be the same

but kenwood are getting better so.....

give the kenwoods a go

bigger midrange cone will give more clarity, while allowing some bass from teh cone area of the actual 6*9

THanks,

As some know I have an older than most model Skyline and really don't want to start hacking up the door trims to fit bigger speakers than can go into the dash relatively easily.

4" splits in the front don't pose much trouble, as the tweeter can go in the cover piece under the dash, but the rear shelf does have a few issues. 5.25 is the largest that will go on the rear deck without spacers, so I made spacers that can accommodate 6 x 9's.

Hence why I ask the question.

Cheers, D

I have read a lot of theory and done a lot of experimentation regarding this subject and as a result you are better off using a 2 way system to reduce the difference in sounds from crossover points and different speakers. I have seen pictures of some massive horn structures to give single 4" speakers enough bass to act as a full range speaker :(

get some good 6" coax speakers instead.

6x9s are sucky and arent really that good.

get some good 6" front splits

some good 6" rear coax's

then a sub or two.

youll never regret it

lol. sif.

if you want good sq and a bit of bass but dont wanna be running subs a decent set of 6x9's in the rear ( i use pioneers ) and some 6inchers in the doors is the best option.

lol. sif.

if you want good sq and a bit of bass but dont wanna be running subs a decent set of 6x9's in the rear ( i use pioneers ) and some 6inchers in the doors is the best option.

OK! Best option opinion please.

TS-A6971E or TS-D691S or R???

Cheers, D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If your current chain of thought is, I'll go somewhere like pick and payless (or equivalent) and causally remove the bit of roof with your BYO grinder then casually weld that into your car... oof. It might sound easy but you will 100% end up with a warped roof. You say you'd prefer some ugly fab work, but I don't know if your prepared for how ugly this will be lol.  I've seen professional welders do similar but easier repairs and still end up with warped panels.  It is reasonable to assume that from your current skill level, you won't be able to do this cut and paste job while keeping flat panels.  Ok, but we are here to learn. This might be the go... jump on car sales, sort by price, buy the cheapest thing with rego and drive it home. This is your new practice vehicle. If you're thinking of doing the cut and paste job, try it on this car. Cut out the panel (hey it's a perfect fit) weld in the panel. See what you think of the results.  Next thing you could try, practice removing the entire roof in one piece by drilling out all the spot welds etc. Have a crack and welding the roof back on.   
    • I've never welded but I own a welder and I've always wanted to learn. In fact I had already looked at a 1 day welding course in Sydney.  I'd prefer some ugly metal fab than anything weak.  I'm challenging myself a lot with this car. For so many years I've just paid other people to do things and I've always been keen to learn and get better.
    • Ok, thats a good starting point.  So before we start.... do you mind if the car say isn't a strong as it was before? My first thought is go excavating for rust. You'll be left with a gaping hole, that will be filled with fiberglass. You could make it look factory pretty easily but yeah, if you never crash it will never be an issue right? Before we look at other options, how confident are you welding? 
    • Oh this is my 1998 E39 5 series. It's worth more to me than financial value. It's a project car for me to love and work on without fear of f**king up something that has lots of value or that I need to keep running.
    • I'm super realistic here. I love the car and want to keep it but I know it's days of perfect condition are well and truly over. I just want a fix that won't come back. 
×
×
  • Create New...