Jump to content
SAU Community

Recommended Posts

The greater Sydney area really needs a racetrack with a few loooong straights and big, open, sweeping corners so the mega HP cars can really stick it to the 'light atmo car' boys....Fatz :pwned::(

:D

Get cracking on it then :)

  • Replies 234
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yogi,

Im not sure, he id run one about 3 months ago, but he lost $5-8K so I dont know how many more he will be running. I dont think he has booked any more days at this stage. I guess if he does not get enough support for these events moving forward he will have to stop running them AKA Moto concepts.

Just wondering guys, down the back straight will I be hitting 180+?

I've got my speed limiter still on but I don't want it affecting my times.

My car is a 190rwkw gtst. :mrt:

definately not! there is no back straight at OP. well there is a short one between turns 3 and 4 but you will be lucky to hit 120 there.

depends how good your entry is onto the pit straight as to whether or not you hit 180. plus in my experience mostly the limiters wont cut in until an indicated 190-195. i wouldnt worry about it mate. it should be the least concern if this is your first track day.

i wouldnt worry about it mate. it should be the least concern if this is your first track day.

He will worry about if its his first track day... You will be hitting about 180 right when you need to hit the first kink/turn and if your not expecting to hit the rev limiter you can shit your pants and at that speed you want to aleast be aware of it.

When your times look shit, its also an excellent excuse as to why you times are poor... Just go with the story that you hit the speed limiter half way down the straight and that you should be 3-4 seconds quicker :P

yeah true, but i dont know that an auto 33 will even hit 180, and being first time out he will be hard on the brakes bro! on the brakes! at the kink :P

good point though, just be aware of it wink, but dont let it stop you.




  • Similar Content

  • Latest Posts

    • I'm not that familiar with R33 tanks. Plastic? Up behind the rear seat between the towers? Or under the boot floor like a normal car? It's the battery that's up between the towers isn't it? So, plastic tanks. Well, um. The obvious reco is plastic welding, which you'd only look at asking someone who's really good at to contemplate trying. The fuel contamination and grot is probably going to make it quite difficult though. Whether plastic or steel - the end of the crack will want to be drilled before any welding or sealing is done. Otherwise it will just continue to wander along until something bad happens. Steel tank? The obvious answer is drain, wash, purge with inert gas and drill the crack end and weld/braze/silver solder/whatever the guys who do that to fuel tanks recommend. I had a crack/hole/leak in the bottom of a Commodore tank (oe was it my ALFA? - can't remember) that I slammed some gorilla snot onto and it never leaked again. It worked surprisingly well. Or, it's time to fab a new tank.
    • MBS206 Did u just take the “Limitless” pill? cause that was way over my head, much respect bro 🤜🏼  
    • I personally haven't been in this situation, however have repaired a cracked radiator using JB Weld and held up until I could replace it with a Honda Accord years ago. Maybe @GTSBoy might have a sound strategy?
    • Hi Dose, I know you'll be reading this thread. Brake pads are going good mate thanks. Anyway, pulled the 33 fuel tank out today because we were limited to a disgusting 480hp on the old fuel pump setup. On pulling the tank, I found the cracks in the photo (I don't think they're leaking, but fuel evaporates quick so hard to tell). What's the best way to repair, or is their a new tank alternative? Thank you.
×
×
  • Create New...