Jump to content
SAU Community

Recommended Posts

Started the engine but gear shifter wouldnt move. With engine running, if i pressed the brake pedal a clicking noise could be heard in the consol at the bottom of the shifter, also turning the key on and off produced the same sound. Presumably this is a solenoid of sorts that locks/unlocks the shift lever.ie a steal stopper.

Eventually I got it the shifter lock to open by fiddling (swearing a lot) and stop starting the engine.

It is now doing it sometimes.

Any ideas, or similar problem experienced?

Ive just had another look.

With engine running the shifter button only goes half in. When i depress foot brakebutton goes allway in and operates of until you turn offf. Then process starts again.

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/
Share on other sites

The clicking is the interlock releasing. It stops you putting the car into gear without having your foot on the brake, therefore stopping you leaping into the garage wall, etc.

All auto's have it.

You cannot move the shifter out of 'P' (and 'N', I think) without the ignition on and the brake pedal pushed.

It's not a fault, it's just an auto.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2135619
Share on other sites

I've been driving the car acouple of months and this is the first time this has happened. Previously i have not been conscious of having my foot on the brake at the time of selecting a gear.Hmmmmmmm?

I must be getting past it and need a wheelchair. Anyway I'm going to see the silver Stager whois just down the road

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2135649
Share on other sites

its a safety measure being developed by the germans. therefore all germans car do that. its to guard against children playing with the auto trans shifter lever and got the car moving. i didnt know the japs adopted this

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2137665
Share on other sites

66yo - I believe you have an S2 in which case the little red button is an overide to the locking mechanism.

If you pass your right arm under your left leg and press the red button with your right thumb while pressing the gear selector nob with your left thumb and pulling backwards, it will come out of P and into gear. In which case you will have backed into the garage wall because you forgot to press the brake pedal with your spare leg.

The red button is useful for moving the gear selector when the ignition is off, and when you're working on the centre console and cant get it back far enough cause it hits the selector.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2137900
Share on other sites

S1 actually. But many thanks. I looked up j-spec 5724 and saw the red button yyou sreak of. My S1 dosnt have it.

It is interesting what Yudy said about this feature being German. The S! I have is a 1996 model so Nissan have been using it for ten years maybe more.

Do Bommerdores and Found On Rubbish Dumps have this feature?

Another interesting feature that Nissan had on the RMR30 Ti was being able to close the electric windows after the engine is turned off, without putting the key back in.Very handy.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2139278
Share on other sites

S1 actually. But many thanks. I looked up j-spec 5724 and saw the red button yyou sreak of. My S1 dosnt have it.

It is interesting what Yudy said about this feature being German. The S! I have is a 1996 model so Nissan have been using it for ten years maybe more.

Do Bommerdores and Found On Rubbish Dumps have this feature?

Another interesting feature that Nissan had on the RMR30 Ti was being able to close the electric windows after the engine is turned off, without putting the key back in.Very handy.

66

dont forget though the 260rs its 2nd car i owned which is japamese. I have driven BMWS most of the time until i came to oz. My fisrt car was my landcruise . so... I drove mostly continental cars all my life until recently.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2139494
Share on other sites

its a safety measure being developed by the germans. therefore all germans car do that. its to guard against children playing with the auto trans shifter lever and got the car moving. i didnt know the japs adopted this

The foot-brake interlock was developed by the Germans, yes, particularly Audi. Americans with less than half-a-brain (most of them, in my opinion) started running litigation suits against car manufacturers for "unintended acceleration." Instead of said Americans taking responibility for their own actions, they blamed the car (a machine, after all) for moving when the gear selector was moved into either Reverse or Drive, causing shock, injury, or - at worst - death as the car lurched backwards or forwards under its own unhindered power...

Audi was the hardest hit in the litigations, and it almost brought them down...

It's not exactly being developed, most of this litigation and the changes to cars happened 20-30 years ago. It's the same reason that early Hyundai's were amongst the first to have the same system on their manual cars, where the engine couldn't be cranked over until the clutch was depressed all the way to the floor.

(See, Hyundai's were good for something - it's a shame that that about covers it...)

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2140133
Share on other sites

Since joining this Forum I am astounded at the details of Auto Enthusiasm that abounds.

A simple thing like not putting my foot on the brake before selecting a gear, has produced a wealth of dispersable knowledge.

We are all the wiser.

Also I think my typing is improving.

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2140188
Share on other sites

Well we all like cars i suppose. Thats why we are into it. But to tell you the truth though i like NA cars better. I think thas where the tech is. dont you guys agree?

For an example the Bmw M5 thats a beast!! The agine is made up of magensium ally and it wiegh no more than 300kg and its a v10!! There goed the niche of the rotary of a lightwieght engine.

But the rotary is still another matter i like it though. Cos i can say my engine redlined @9500rmp stick!! hahahahah

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2140717
Share on other sites

Well we all like cars i suppose. Thats why we are into it. But to tell you the truth though i like NA cars better. I think thas where the tech is. dont you guys agree?

For an example the Bmw M5 thats a beast!! The agine is made up of magensium ally and it wiegh no more than 300kg and its a v10!! There goed the niche of the rotary of a lightwieght engine.

But the rotary is still another matter i like it though. Cos i can say my engine redlined @9500rmp stick!! hahahahah

Hey Yudy,

We all have M5's as well, we keep that talk to the M5 forum though...

:P

Link to comment
https://www.sau.com.au/forums/topic/116127-sticky-topic/#findComment-2145746
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Starting with issues 1 - 5, we have already run into a problem...!  Issue #4 contained 2x front brake calipers, instead of 1 caliper and 1x steering knuckle. Will have to call DeAgostini on Monday to sort it out. Anyway here's some photos.  Issue #1 is the front bumper, headlights and number plate. Issue #2 is the front wheel (with "We produced with spartan air." text on the centre cap!) and tyre, the front lip spoiler and cylinder head cover with ignition coils under the centre cover... which will never be seen again. Issue #3 is the bonnet and cylinder head. Issue #4 is the front strut, brake disc (with laser etched metal discs) and brake caliper. I stopped here because of the issue with the missing steering knuckle.  Next update will be #5 - #10 in a few weeks.
    • DeAgostini is one of a few companies that release quite large (the largest commonly available size actually) 1/8 scale models in a series of weekly issues over 100 - 110 instalments.  They release different models for different markets and DeAgostini Japan have release the BNR32 Skyline GT-R Nismo last month. I've made two of these 1/8 scale sized cars (one an R35 GT-R from 2012 - 2014, the other I'm just about halfway through, a BNR34 Skyline GT-R from the 2Fast 2Furious movie) so when this R32 was announced there was no way I could ignore it as it's my favourite out of all Nissans.  Each issue costs around $20 so it costs about $2.2K when completed. I suppose it is very expensive for what it is, but the quality and details are really very good, and there are many "gimmicks" like fully functioning exterior and interior lights operated with a remote control, working steering, all doors/bonnet/boot/fuel lid open and close, the side mirrors fold in and it even has a speaker for the engine revving sounds when you turn the lights on.  Each issue comes with a magazine that tells the story of the BNR32 Skyline GT-R Nismo from the first design stages of the BNR32 to Group A homologation and the various racing version that were run in the Japanese Group A and JGTC, and Australian Group A.  So I plan to update the build in this thread 5 issues at a time.  https://deagostini.jp/r32/?srsltid=AfmBOooKjxDc4EUK2rmXqMBPgyHfFJ24s4oEPJBNpnF-lFlsRoW0PE6P
    • As per title.. has anyone used so far? Keen to hear results, comparisons. In the market for a new mani for my new turbo. Any issues cracking?
    • Re read everything that has been written about this in this thread.. Let us know if you're still confused.
    • This would be a new pump with new gears. I'm just unclear on whether it's a good idea to run more oil pump flow if you don't actually need said flow. Oil level is set a minute or so after shutting off a warm engine so wouldn't the high RPM oil level in the sump end up lower all things equal? Plan is OEM clearances, main concern in my mind is whether the OEM pump can keep up with the flow requirements of any additional oil coolers.
×
×
  • Create New...