Jump to content
SAU Community

Microtech Lt8 Sequencial Fire V10

XTC333
 Share

Recommended Posts

XTC333 Apprentice

XTC333

Posted
Posted (edited)

Hi all

I've decided to bring my r33 gtst back to standard and am selling this ecu. $350 delivered. This ecu allows you to run without an air flow meter. THis ecu together with 550cc injectors T04E turbo FMIC and manual boost controller running at 19psi produced 266rwkw. It's tuned for this set up. I'm still thinking about whether I should sell the turbo or not because I'm thinking of putting this in my bro's soarer. I have written down the instruction for wiring in for this ecu. Very simple really.

Thanks all for interests in this ECU. THis ECU has now been sold, pending payment.

post-28574-1146662506.jpg

Edited by XTC333
Link to comment
https://www.sau.com.au/forums/topic/116266-microtech-lt8-sequencial-fire-v10/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      Is the 650rpm idle on the rb25det neo for stock cars only? I've never had my car before and after tuning it to idle at 650rpm when cold. Always idle's cold around 1100rpm, and then drops to about 900-950rpm. I've heard the r33 gtst's idle there. 
    • redzed
      RB25DET 5 speed gearbox, Cusco Super Single clutch, RB26DETT standard cams in/ex, HDI GT2 intercooler

      By redzed · Posted

      Series 1 RB25DET 5 speed gearbox, push type, 1st and 2nd gear syncros worn, may need bearings. Comes with quick shift, Tomei gear knob, release fork, bearing carrier, master and slave cylinder. $850. Cusco Super Single clutch,assembly, 225mm, used, comes with a Direct Clutch solid centre 5 puck ceramic clutch plate. $290. RB26 cams used, excellent condition. $280. HDI GT2 intercooler, excellent condition, has 3 inch piping welded to inlet and outlet. $250. All items located in South Eastern Melbourne. Please PM me if interested.
    • Sleepergm
      Changing to titanium muffler tips

      By Sleepergm · Posted

      Hi all, I’m currently running a str pipe hi low hks exhaust and downpipe. Was wondering if I change out muffler to a titanium one will it change the sound of the exhaust? Plus I have always liked the look of the titanium pipes … anyone have recommendations to one?    side note already have titanium intake pipes. 
    • Skip33
      Series 2 R33 GTS25T?

      By Skip33 · Posted

      I looked up my other car that is a R33 GTST series 1.5. Anyone able to confirm what a Aero Form Bumper is?     (1G) 2 Door Coupe; (2GK + 11V) RB25DET; (4B) 2WD HICAS; (7F) 5 Speed Manual; (14G) Super Fine Hard Coat; (15U) Large Rear Spoiler + Aero Form Bumper + Rear Wiper (Aero Selection)
    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Ha ha, all good! I've almost caved in and realised I'm buying one.  I know myself well enough by now that I will start chasing ADHD butterflies half way through building it and not finish it so I'm better off spending the extra money buying one instead of making one just so I can get into straight away.  I would very much enjoy making one as fabrication is probably a strength and definitely a passion but I don't want that to be at the detriment to the car I'm ultimately building it for! There's some pretty good ones around for ~$1100 at the moment so I think I'll just go that way.  At the end I sell it or as mentioned, get another project to make further use of it! Thanks gents.  
×
×
  • Create New...