Jump to content
SAU Community

Rear Coilover Set Up

xr8eater
 Share

Recommended Posts

xr8eater Experienced

xr8eater

Posted
Posted

i just put some coilovers on the rear of my R33 gts-t i set the pre load and ride hight to with the c spanners. and yes i mesured it accuritley. i put the shocks on my car and mesured the distance from the top of the rim to the guard it was like a couple of cm diffrent is this normal or should i adjust the ride hight to match???

also there is two diffrent tyers on the rear could this be the problem???

Link to comment
https://www.sau.com.au/forums/topic/116649-rear-coilover-set-up/
Share on other sites
sedanlover Contributor

sedanlover

Posted
Posted

hey there, i have same problem...but i have the same tread on the rear. i'm guessing that would make it be out so much, (especially if you have one tyre more worn than the other)

mine was only a coulpe mm out either side, but i think thats because of my slack measurements.

i say its the tyres.

MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted

mine was out. i set coilovers based on number of threads on the adjustment, but the wheel to guard measurement was like 2cm out. probably due to hitting a few ripple strips every now and then...

just use wheel-guard and adjust as required

  • 6 months later...
salad Veteran

salad

Posted
Posted

Adjust it so that the centre of wheel to guard heights are the same, not the amount of preload. For the amount of load that the car places on the spring seats, preload is negligable once the weight of the car is down.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...