Jump to content
SAU Community

Rb20 Replacement

Jaystar

By Jaystar,
in Queensland

 Share

Recommended Posts

fat31 Community Regular

fat31

Posted
Posted
Hey all

Just wondering if anyone has ever had a rb20det replaced in there car?

If so how much did it cost you, where did you get it done and were you happy with the work.

Brisbane only though.

Thanx

yep had plenty of experience with rb20 replacements always been happy with result, just some advice id stay away from tokyo toys racing they will rip you off and stuff you around. as for price it depends where you go it could cost anywhere from $1000-$1500 for motor and about $600 for a gearbox. diy replacement is very easy as the rb20 is quite a simple motor to work with.

The Dan Grand Master

The Dan

Posted
Posted

Engine should cost you around $1500-$2000 for a decent one.

6-8 hours @ $55/hour = $330-$440 + any fluids, belts, filters, hoses that may be required.

I would budget $2600 and you should be ok.

I thought you were getting your rebuilt by someone at the moment Jay?

Jaystar Collaborator

Jaystar

Posted
  • Author
Posted
Engine should cost you around $1500-$2000 for a decent one.

6-8 hours @ $55/hour = $330-$440 + any fluids, belts, filters, hoses that may be required.

I would budget $2600 and you should be ok.

I thought you were getting your rebuilt by someone at the moment Jay?

i was going to get it rebuilt and modded but then started to think about selling and then this happened and was undrivable so now am getting another rb20 put in and will decide what to do.

probs move on.

The Dan Grand Master

The Dan

Posted
Posted
i was going to get it rebuilt and modded but then started to think about selling and then this happened and was undrivable so now am getting another rb20 put in and will decide what to do.

probs move on.

Well I can still do a full rebuild for $3200 for you. That includes engine removal and refit....plus complete head service with valve regrind and new stem seals + guides...plus full block service, crack test, re-deck, hone, all gaskets, seals, oil, oil filter and labour. For an extra $100 I can get the injectors fully serviced as well.

Anywayz...just another option for you...

What happened to it by the way?

Col-GTSX Grand Master

Col-GTSX

Posted
Posted

Id go the rebuild...

Ive been burnt twice with half cuts and unknown motors...

Rebuild is worth a couple of bucks more and at least you will know what you are getting. Plus its newer this way also...

If your not mechaniclly minded and dont know any trust worthy workshops, then Dan is ya man....

The Dan Grand Master

The Dan

Posted
Posted

Love the kind words fellas...keep 'em coming.

And yeah like Col said, if you aren't mechanically minded, know anyone who is, know anyone who knows anyone who is, know anyone whose cousin's friend knows someone who is....then I'm your man :D

But honestly, even if you are mechanically minded you shouldn't tackle a rebuild with at least someone who has done it many times before to guide you. It's a little more than slapping nuts and bolts together.

The Dan Grand Master

The Dan

Posted
Posted

You mean you actually think mechanics do something during the day....nah we just lean up against the hoists and sink beers, make up stories, laugh at random comments, then drive all the cars out and charge the customers for work we never even did.....ahhh it's a great life.

dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted
Well I can still do a full rebuild for $3200 for you. That includes engine removal and refit....plus complete head service with valve regrind and new stem seals + guides...plus full block service, crack test, re-deck, hone, all gaskets, seals, oil, oil filter and labour. For an extra $100 I can get the injectors fully serviced as well.

Anywayz...just another option for you...

What happened to it by the way?

Compleatly unrelated to the topic. But injector service for $100??? Including labour!? Dude thats good hey.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      gauge needle removal

      By JC71 · Posted

      I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Roy
      A Boy's Love For His Rb20

      By Roy · Posted

      Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • GTSBoy
      Wheel refurb?

      By GTSBoy · Posted

      Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • GTSBoy
      R-chassis INNER tie rod torque spec?

      By GTSBoy · Posted

      Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...