Jump to content
SAU Community

R32 Gts-t 93' Price Drop *$8500* Sold Sold

DRFT32
 Share

Recommended Posts

DRFT32 Enthusiast

DRFT32

Posted
Posted (edited)

CAR: Nissan Skyline R32 GTS-t

YEAR: 1993

COLOUR: Wine Red

TRANSMISSION: Auto

LOCATION: Central Coast NSW

KM's- 192000

CONDITION: Appart from usual nics (vents etc) its in good condition

REASON FOR SELLING: opportunity for upgrade has arisen

MODIFICATIONS:

Dr DRIFT chipped ecu

Full 3" exhaust with hks copy split dump pipe

front mount intercooler

Arias Forged pistons 20thou ovesize

ported and polished heads

1mm oversize valves

match ported manifolds

ported exhaust manifold

high flowed VG30 Turbo 450hp

Sard Adj Fuel Reg

Fully balanced and machined bottom end

k&n flat panel filter

standard injectors

R32 GTR Fuel pump

Std Blow off valve

Caltex Vortex 98

Lowered on super low king springs

stock auto transmission

208.1 RWKW at 1.4 BAR

All reciepts can be shown

PRICE: $8,500 including the wheels shown...this is very cheap for what has been done..

PM or phone Aaron on 0412 039 232

post-8646-1147325961.jpg

post-8646-1150112765.jpg

post-8646-1150112779.jpg

post-8646-1150112795.jpg

post-8646-1150235610.jpg

post-8646-1150235623.jpg

Edited by DRFT32
  • 2 weeks later...
DRFT32 Enthusiast

DRFT32

Posted
  • Author
Posted

yes it has a RWC and the car will have 12 months rego on it for NSW because it runs out on the 22nd..if you dont was me to register it in NSW let me know..i will get some interior pics today for ya's. the gearbox is fine...still holding up but $2500 drive in drive out i would convert it..i was about to but now selling it i'm not..but the gearbox is fine. the engine is about 20,000 kms old since the rebuild so its fine..i have put the standard turbo back on the car incase i dont sell it and have to wholesale it but i can put the high flowed one back on which is only 5000km's old. the standard turbo's seal is running thin so the car has a bit of smoke when it climbs boost with this turbo on it. yes i do have a dyno sheet and this was before the exhaust was completed and the ecu re chipped so it should put out more than 208 plus if you convert it manual it should put out more again.

thanks guys

post-8646-1150154987.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      Don't take it as a guarantee. It's all a game of statistics. And on top of that, smooth over a thick layer of "quality of spanner spinning" as a further Gaussian curve of probability of failure. You play games at anything above ~400 HP, and you're using up margins in terms of engineering and luck.
    • Curlyfred
      Rb26 iron block limit

      By Curlyfred · Posted

      Aye, everything is being touched and all the parts that are responsible for the oiling issues are also fixed. (Crank collar, billet prp oil pump, head return to sump, yada yada yada)  Everything used is of reputable brands like greddy, prp etc. My tuner did mention we’d keep the torque on the “lower” side.   glad to read that my engine won’t blow up on me lmao 
    • GTSBoy
      What's this Foreign Object?

      By GTSBoy · Posted

      It's a fuel pump. EFI, high pressure, but specs otherwise unknown. A bodge job.
    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      800 engine horsies is fine. Will need all the obvious upgrades. Rods, pistons, oil pump, big sump, sump breathing mods. Build for revs because revs are power with less stress on the bottom end compared to boost. Keep the torque down in the midrange, either by limiting boost or timing.  
    • Curlyfred
      Rb26 iron block limit

      By Curlyfred · Posted

      Hiya guys,    i’m currently in the process of getting my rb26 built. everything is being replaced with better/upgraded parts or oem when that’s good enough (which isn’t alot lol). someone earlier mentioned to me that i’ll be screwed cause the iron block can’t take 800hp (to the engine, not wheels) which is what it’s being built for.  what do you guys think about this, am I cooked or na? The guy building the engine will also do the mapping as he is “the guru of old nissan engines” here in Belgium. I know the mapping makes a huge deal so i’m not concerned about that.    I honestly he’s talking shit cause he’s that kinda guy but a second opinion never hurt anyone! cheers in advance! 🫶🏻
×
×
  • Create New...