Jump to content
SAU Community

Door Open Sensor

MANWHOR3

By MANWHOR3,
in Car Audio & Electrical

 Share

Recommended Posts

MANWHOR3 Proficient

MANWHOR3

Posted
Posted

Hi guys,

Can someone please help me?

Basically, from what I understand, the door sensors on the r33 are on different circuits. i.e. when the driver's door is opened and the key is in the ignition, there is a chime noise. But, when the passenger door is opened, there is no chime noise.

If i'm hooking up an alarm, how can I get it such that if either door is opened, the alarm will be triggered? i.e. where can I tap into a wire?

The reason I ask is because my alarm installer did a dodgy job.

Link to comment
https://www.sau.com.au/forums/topic/117416-door-open-sensor/
Share on other sites
danielr34 Collaborator

danielr34

Posted
Posted
Hi guys,

Can someone please help me?

Basically, from what I understand, the door sensors on the r33 are on different circuits. i.e. when the driver's door is opened and the key is in the ignition, there is a chime noise. But, when the passenger door is opened, there is no chime noise.

If i'm hooking up an alarm, how can I get it such that if either door is opened, the alarm will be triggered? i.e. where can I tap into a wire?

The reason I ask is because my alarm installer did a dodgy job.

Hi mate go to the thick wiring loom in the drivers kickpanel (to the right of your left foot) and find a thin red wire, it is one of 2 and it is the thinner one out of the 2, you can tell because the other one is a little thicker in diameter.

I have been fitting car alarms for Security In Motion for the past 5 years and if we don't know nobody does!

Next time just call us.

MANWHOR3 Proficient

MANWHOR3

Posted
  • Author
Posted

Can you explain something to me?

The previous alarm installer just soldered a wire onto the actual switch on the driver's door. But as I said above, the passenger's door is on a separate circuit.

So just to confirm, doing this red wire will have it hooked up to both sensors?

Cheers

frx026 Proficient

frx026

Posted
Posted

To Confirm in a r33 the door sensor pick up wire is the thin red wire in the drivers kickpanel.

And as how that has been done, i have to repeat myself

It sound like your car would be fairly easy to steal.

Why?

Well not because one door does not trigger the alarm. But because the original installer obviously had no idea what he was doing. The r33 uses one wire to sense both doors opening, so having only one working means that installer -

- did not have much skill

- does not know skylines

- has probably left the alarm box in your kick panel or just under the dash

- was working to a price

I think what you should do is have a look under your dash, drivers kickpanel to see if you can see the alarm, if you can, dont bother taking it back to your original installer, take it to someone who knows what the are doing and get the entire alarm relocated and rewired.

Sure its extra money, but really from what you have said, it would most likely take less than 30 seconds to steal your car at the moment.

If you are looking to get it done fire a PM at CHRIS ROGERS, he is the man with the install contacts.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted (edited)

no it doesn't.

depending on car they are two different leads in two different spots.

32,33,34 &35 are diode isolated from the drivers door. all have two places to get the wire. I do not get it in the usual spot. colours are all similar.

inthe case of a S2 33 and 34 the smart entry system will foul the alarm if tied in at that point.

Edited by Chris Rogers
  • 8 months later...
Keeper Proficient

Keeper

Posted
Posted
Hi mate go to the thick wiring loom in the drivers kickpanel (to the right of your left foot) and find a thin red wire, it is one of 2 and it is the thinner one out of the 2, you can tell because the other one is a little thicker in diameter.

I have been fitting car alarms for Security In Motion for the past 5 years and if we don't know nobody does!

Next time just call us.

WOOHOO this is so helpful, hey its to the right of your RIGHT foot, I got confused for a little there!

Its the loom that continues back under the carpet along the right side of the car :)

J_Red33 Experienced

J_Red33

Posted
Posted (edited)

I'm not sure this is completely the same problem, but I have an alarm installed that triggers on both doors which are on separate circuits, but the interior light no longer turns on when the passenger side door is opened. My car originally had the factory keyless entry. I'm guessing it's probably a bad idea to brigde the two door wires down at the kick panel. Is there possibly any other way I can overcome this problem?

Was thinking maybe I need to link the interior light circuit to the passenger door switch via a diode, but I have no idea which wire the interior light trigger is.

Any help here would be appreciated. I don't really want to take it back to the installer they were quite rough with my interior trim after commenting how 'Nice & clean' my interior was (GT AUTOSOUND, DON'T GO THERE! If you truely value your car).

Edited by JazzaR33
Chris Rogers Grand Master

Chris Rogers

Posted
Posted
I'm not sure this is completely the same problem, but I have an alarm installed that triggers on both doors which are on separate circuits, but the interior light no longer turns on when the passenger side door is opened. I'm guessing it's probably a bad idea to brigde the two door wires down at the kick panel. Is there possibly any other way I can overcome this problem?

Was thinking maybe I need to link the interior light circuit to the passenger door switch via a diode, but I have no idea which wire the interior light trigger is.

Any help here would be appreciated. I don't really want to take it back to the installer they were quite rough with my interior trim after commenting how 'Nice & clean' my interior was (GT AUTOSOUND, DON'T GO THERE! If you truely value your car).

are you sure the alarm works on bith doors?

bridging the wires will only make the lights on buzzer show on both doors not jst the drivers one.

J_Red33 Experienced

J_Red33

Posted
Posted
are you sure the alarm works on bith doors?

bridging the wires will only make the lights on buzzer show on both doors not jst the drivers one.

Yeah pretty sure it works, confusing I know, but that's the way it's working at the moment. Not sure if it had anything to do with the factory central locking system as both the door wires did go to that. It has been removed so I'm thinking that's the reason.

  • 1 month later...
are33 Proficient

are33

Posted
Posted

This has probly been solved i havnt read through the thread, but i made this a while ago when i disconected mine, Its a bit dodgey but its easy to do if you can make sense of it :P

http://www.boostcruising.com/forums/index....howtopic=167222

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      RB25DET Solid lifter conversion

      By Dose Pipe Sutututu · Posted

      Cheapest option, find a NEO head. Put in good springs, decent cams, and send it to the moon. I rev mine to 8600RPM, gets me about 232km/h down the main straight at SMSP bouncing off the limiter in 4th. I've never dared to grab 5th 🥲
    • pogman
      RB25DET Solid lifter conversion

      By pogman · Posted

      Gday mate, Personally in my car i run 450kw in an s2 rb25 so also hydraulic lifters and have always run it to 7500 RPM and using some baby 256 poncams with new but stock springs and retainers. While i cant speak on any experience with solid lifters i personally have had no issues with my hydraulic lifters which were just cleaned and set in an oil bath before assembly over 7 years ago. Over 8k RPM is cool IMO and if you are using the stock gearbox or just a box with longer ratios the higher rpm certainly could aid to maintain boost into the next gear as that was always something i struggled with as i have a 3582r also but a hypergear equivalent could aid that issue. In summary i would make a choice on the cam you want to use first then decide which springs and retainers work best with it and then you can toss up if you really need the solid lifters, if the car is mainly street i would learn towards keeping the hydraulic lifters as when installed properly and nothing too hektik going on around them they do the trick.  
    • GTSBoy
      R32 GTST - 600KW+ RB28/CD009 Build

      By GTSBoy · Posted

      Yucky. Things haven't gotten any better though. Now you have Emerson and Honeywell pushing these massive DCS/Scada things with proprietary hardware. They're not a PLC, they're not a computer, they're a...distibuted PLCish/DCSish monster of thing, that only they can program because they make the barriers to entry for anyone else so fricking high. And their developers are all located in the third/developing world (and India, in case anyone does not include that place in that category) and there are terrible failings of the ESl variety, of the care and common sense variety, and f**king forget about Functional Safety. Not a one of them has any idea what it means to comply with an IEC 615xx series standard.
    • niZmO_Man
      Is r33 gtr steering wheel the same as the gtst?

      By niZmO_Man · Posted

      oi (you're right though)
    • pogman
      Low oil pressure after WOT

      By pogman · Posted

      All of the ECU grounds are to the chassis, the IGN grounds are to the cylinder head and i believe all the OEM body harness are left in original locations, im trying to work out if i can tell if the sensor voltage itself is losing any power to it from the very low ECU voltage. But yeah a manual pressure gauge will help in picking which path to actually chase. Also please dont bully my wiring plan i never designed it to be universally understood hopefully it still can make sense to you, im a wiring virgin.  1 thing i have just noticed the pressure sensor in question relays both pressure and temperature, the temperature reading holds nice and steady despite the low ecu voltage but the pressure reading is the one that jumps around alot so maybe it is really a pressure issue? wiring plan.xlsx
×
×
  • Create New...