Jump to content
SAU Community

Recommended Posts

I want to get the fuel pump out my tank and have a quick look at it and see whether the internal filter needs cleaning.

How do I go about this? Do I have to drop the whole fuel tank out and remove it from the top?? I have seen in some other cars there is an access panel from say the boot or whatever that makes removing it pretty easy without pulling the tank out - anything like that on the R33 ?

Link to comment
https://www.sau.com.au/forums/topic/11783-removing-fuel-pump/
Share on other sites

no tank dropping required whole assembly comes out through the boot

acess pannel in the boot

then unscrew the plastic cap and remove assembly from in tank

i did this once but i dont recomend doing this it is a dangerous procedure and the whole boot fills up with fuel vapours

one spark and boom you now have no face

aswell as the bad effects fuel vapours can have on your lungs

after 5 min of fiddling inside the tank i was completely ****ed up

i had no idea how high you can get on fuel vapours

not a good high mind you killer headache and loss of balance

and also

spinnin`...

spinnin`....

spinnin`

make it stop

hehehe..mygtst - I don't intend on standing there inhaling the stuff to get high :) I'd take it out in the open and like v-spec said make sure most of the fuel is out of it first.

I know petrol is smelly stuff. Shoulda seen when I changed my fuel filter.. petrol dripping everywhere ..and i did that in the garage :D

So where is the panel? I had a look in the tyre well and couldn't see anything. Is that the plate near the fuses and battery behind the rear seat (yes, remove battery first, safety first, blah).

predator.. haehaeh wat a co-incident. i was thinking about the

same thing and gave it a try...

what MYGTST said is right. well right from what i could see.

the cap is soo hard to turn cause of the rubber seal. once i pulled

it open the pump sat all the way down at the bottom so i suggest

emptying it as much as possible.

I'm not sure how to take the pump out tho.. it was very cramped

for me.. Let me know how u go.

...more to the point - how does it go back? apparently it sits at the bottom of the tank face down and sucks. If I just pull it out I might not be able to put it in the proper position - causing major probs for fuel sucking.

the pump sits on a metal bracket which is clipped in place all you have to do is unclip the metal bracket and it comes out with hoses and attacments

the pump is clamped to the bottom of the bracket so you simply clamp it back in the same place once your done

to remove the assembly you need to feel inide and slide the bracket up and to the side and it unlocks

the access panel is in the raised section of the boot on the right hand side and yes the plastic cap is a pain to get off its so tight

i recomend removing the battery from the car during tank opening

less chance of sparks

byt he time you figure out the how the bracket comes out you will be well and truly high even if your tank is almost empty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
    • Awesome writeup and details. Thanks for sharing the story so far. I can relate to parts of it with my previous car and some of the issues I had to deal with.
×
×
  • Create New...