Jump to content
SAU Community

Is It Possible To Bypass The Loom Plug For A Head Unit?

D-limo

By D-limo,
in Car Audio & Electrical

 Share

Recommended Posts

RANDY Veteran

RANDY

Posted
Posted

First, go to Jaycar, Strathfield and Dick Smiths and see if there is a harness adapter for your headunit. (from your unit to ANY car harness)

That way, you don't need to make up the plug or solder wires directly onto your headunit, just plug in, and then crimp the other end of the loom to fit the stock harness.

Failing that, I don't know how easy it will be to work out which pins on the back of the HU are for what. A multimeter will only work when there is power applied, and then finding the right pin for power first go sounds unlikely. If you apply power to the wrong pin, you may blow something up. If you open the unit, a trained eye could probably verify which pin is for what, but that's not me!

D-limo Veteran

D-limo

Posted
  • Author
Posted

The hanesses cost like $45.. And the unit is probably worth that 2nd hand.. So yeah I'm trying to do it cheap as possible lol.

You're right. Finding wich pin is for what is going to be the hardest thing to figure out. I was hoping it was that easy. Can anyone confirm? Also is there spec sheet or the like I should be searching for that would contain what each pin does?

MANWHOR3 Proficient

MANWHOR3

Posted
Posted

You can do it, you have to open the rear cover of the headunint and solder onto the plug socket. trust me mate, not worth the trouble.

If it's not worth buying the wiring plug, then it's not worth installing it like that.

It'll be a shit job. difficult. probably fail too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      R34 power steering

      By drifter17a · Posted

      Thanks, plan is to drain all fluid tomorrow and do smoke test to find out the leak.   Appreciate your help and want to understand how the system work. So cooling is achieved by the long loop not any rad? The diagram seems to suggest it connects to somewhere inside the cabin and I thought that is a cooler inside firewall. If you look at the diagram it seems to show it connects to something inside firewall. I tried chasing it but not easy unless I take loads off   i am confident pump is good as fluid goes in and it gets soft( steering) but as soon as I turn engine off , loads of bubble come to surface and overflow. When engine is on , fluid level is below minimum but when off it shoots off and thinking it is sucking air in. I suspect aluminium pipe may have a crack line or whole   smoke test with no fluid should be a good start and if needed will remove the pump   In addition, the one going under the engine bay is high pressure line and one directly connecting from pump to resorvoir is return/ low pressure?   finally I searched and suggestion is to use dexron 2 but that is discontinued so bought dexron 3 as all research suggest it is compatible and shouldn’t cause any issues/ blow seals. I bought two liter of dexron 3 motul atf
    • GTSBoy
      RB25 S2 Idles but doesn't want to rev

      By GTSBoy · Posted

      Don't worry about. Just don't try to drive hard enough to make boost and you'll be fine.
    • GTSBoy
      R34 power steering

      By GTSBoy · Posted

      Yes. This has already been said. It is a loop of hardline in front of the radiator. Because.... the pump is on the LHS and the steering rack hydraulic connections are where they always are on a RHD steering rack....on the RHS. The high pressure line goes down under the engine, along the crossmember, like it does on all Skylines. Don't just throw expensive braided hoses/other kits at it. Work out what is wrong and fix that.
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      Still got the afm on the intake, clamps are shut tight, only loose hose is the one that goes from the j pipe towards the IACV, since it's next to impossible to find a factory hose and the barbs are different sizes (I'm still using clamps on this hose to try and help it seal on the iacv side) I've ordered parts to make up the hotside of the intercooler pipes, I'll plumb it in and see what happens in a few days I suppose The turbo's internally gated, can I just unscrew the tension rod to let the gate open?
    • McGarryR32
      T56 In Gtr

      By McGarryR32 · Posted

      Did this ever go further ? Would love some updated info 
×
×
  • Create New...