Jump to content
SAU Community

Recommended Posts

hey guys a mates r33 gtst out of the blew has started to idel very rough and it begain to over heat so all hoses have been changed and flushed the system and added coolant.... also when car is turn off water in the overflow bottle is bubbling???? anyone know whats going on

all help is much appreciated???

take the radiator cap off and let the engine idle, if the water bubbles and froths up and has oil in it then u prolly blew a head gasket, take it too a mechanic they got a thingy they put on there and if it loses compression etc etc.

I guess this wont help, but anyway...

Had the same prob on my BMW, the earlier owner had changed headgasket, rebuild the head, and changed cooler along with some other things, when i bought it.

It acted the way you describe, but there werent any oil in the water etc, and if it idled for a somewhat long while it started to stutter, and the water in the overflow bottle started bubble.

Someone mentioned i should check if there were air in the watersystem, and there were some, got it out and now its a whole lot better.

Probably wont help you but who knows, it might :thumbsup:

bleed the radiator again, using the tap near the plenum that has the label "do not open when hot"

other test is for exhaust gas in the cooling system.. they put it over the cap and it changes colour if gases are in it...

for $330 for a cometic metal gasket and time if your mechanically minded then you can fix it up easy and cheap if it does show gas.

water is going out the exhaust brother, Chemical testing the system is the way to go, blown head gaskets dont always blow to an oil gallery, most common is cylinder to cooling system. other test is to pressure test cooling system with spark plugs out, then crank engine, if water is blown out of spark plug tube, thats bad.

something has caused the car to overheat, repair leak, check thermostat, flush radiator. Blown headgasket is the result of something else failing.

' date='23 May 2006, 06:34 PM' post='2194735']

could it be the water pump?

where does the leak go to?

Edited by Bezerkly

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh... literally every time i jump on a forum, see an instagram post or see an engine bay at a car show, i get an idea and add it to my 'to do' list. So what started off as, hey can u just make a couple of intake hard pipes because my dumbass bought the wrong apexi kit, blew out into a 2 week job including braided brake lines & custom bash kit for the front lip haha.  Getting Luke from A4E engineering to make a full custom exhaust with a controllable aes dump valve so i can actually switch between quiet and loud, because right now its just loud all day every day. Then after that go and get the tune redone flex e85 & 98 as i get bugger all milage from e85, makes going for longer drivers difficult
    • Car looks clean as. You ended up getting quite a bit done 😂  So what's the plan for the exhaust? 
    • The only Neo rods that were any different to any other RB25 rods were the DET ones, and they were the same as RB26. Here is a Neo DET rod. O5U part number visible. Here is a post in a thread here on SAU with evidence from someone who has done this before. There are photos in the thread of normal RB25 rods.  
    • Sure, but why assume that will be the case forever? And why assume you'll be able to do an oil change to swap back to a stock drain bolt before that happens? And does it even matter when I change the oil at fairly short intervals? Life can be funny sometimes and unexpected things can happen. Like breaking a collarbone so you can't do any work on your car for a few months but the oil change is due so you have to take it to somewhere and hope they don't do something stupid like stacking the new drain plug washer on top of the old one.
    • Do u know how to identify the rods are rb25 or neo ones? Can u look into the pics and tell me is they de or de neo ones. Its confusing becoz my motor has de neo head but block is 25de 75t, so really confusing me about rods, crank.
×
×
  • Create New...