Jump to content
SAU Community

Recommended Posts

i have the following mods:

fmic, turbosmart dual stage boost controller, apexi s-afc 2, k and n pod filter.

before i got the safc2 installed i tried boosting it too 12-13 psi and i was getting this hiccup in the engine when i put my foot to the floor, and i thought it would have to be the a/f ratios, so i decided to get the safc 2 as the power fc was way out of my budget, for $900 i got the safc 2, had it installed and dynoed.

as it was being dynoed on high boost of just under 13 psi it was doing that hiccup thing again, and eventually the guy must have tuned them out cos it wasnt doing it anymore. so i was happy. took the car home and for a few days it was fine, but then it started doing the hiccup thing again, not as often as before but still there and very embarassing when wanting to drag sumone, the whole car would shudder for a second or 2, and keep going, it would literally jerk.

does anyone have any idea what this could be and how to fix it???

sumone said that the boost level was too high and was blowing out the spark in the plugs, so i bought new ones, ngk platinums and regapped them to 0.8 mm, but no improvement, the only way to avoid it is by using a maximum of 75% throttle.

any help would be appreciated...:D

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/
Share on other sites

thanx for the replies.

the safc 2 takes care of the boost cut, could be fuel pump,

i did turn my boost down a bit, but no help, if i turn it down anymore there wont be any point boosting it

i think the best bet is to get it redynoed but i thought there might be a simpler solution

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-211025
Share on other sites

if this hiccup is around 5000rpm, then it is most likely the same spark problem that all the R33 owners get after boosting their cars.

Have a search in here for "misfire" or "5000rpm" and you'll see other peoples replies.

I think they were saying to gat the plugs to 0.7 (I think)

good luck.

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-211380
Share on other sites

Change your fuel filter, you should do this regularly anyhow.

The fuel pump issue, will play out like this;

* try getting up to 5000rpm in 1st using light throttle, then at 5000rpm cruise put your foot flat to the floor. If the same issue occurs straight away it's probably not your fuel pump. If it allows you to gun it through first and then starts doing its thing in 2nd or 3rd then the fuel pump might be at fault.

The spark plugs maybe too hot for the load. Try a range or two colder. Buy cheap copper ones.

Check your base timing.

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-212547
Share on other sites

ive just changed the fuel filter so its not that, it was doing it before and after the change.

i dont think it happens in 1st at all, but in 2nd and 3rd it does only when i put my foot to the floor on high boost.

i think the heat range for my plugs are a 6, could b 7, cant remember

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-212559
Share on other sites

My car is doing the exact same thing, I got new spark plugs put in today gapped .8mm. Its been on the dyno yesturday and today and turning the boost down from 1bar isn't helping. I have a standard ECU which will be replaced by a powerFC as soon as I get around to ordering one.

Yesturday I only managed 175.1hp on the dyno.

Tommorow I might have another go.

Mark

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-212906
Share on other sites

If it happens when you hit 2nd or 3rd from a standing start test and doesn't act up at all through 1st gear then the fuel pump is perhaps at fault.

When I say standing start or rolling start run at 5000rpm I mean going from 1st through all the gears to 4th as if racing. You might only get to 2nd when it occurs. If it occurs in the later gears and not the 1st fueling is the issue.

It could be ecu 'fuel cut' also.

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-214337
Share on other sites

i was told the safc 2 removed fuel cut?

becos i had a fuel cut defender in there before i got the safc 2 and when i got the safc 2 installed he said i dont need the fuel cut defender anymor

i'll take the car for a thrash and see if it does it in 1st or not...

i was actually driving it pretty hard yesterday on high boost and it didnt do it once, seems to do it when ever it feels like it

Link to comment
https://www.sau.com.au/forums/topic/11897-boost-problem/#findComment-214401
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Everyone is too used to learning from places like HPA "how to tune" and what to expect at what point, rather than being able to see "The computer says I'm in cell with Row = 8, column =4, and I can see my fuel is lean, so lets add more" Everyone wants "real units", which helps for someone picking it up for the first time and seeing how bad the tune is if they're not used to touching it.   However, I think for most of us who want to play with it, you're 100% right, we're only needing to learn about it for OUR CAR. Which makes it great, and we don't need to care what the real values are, we just need to know which cell it is, that's causing the lean or rich point, or that we want more ignition timing or less. But again, everyone wants everything super you beaut and nearly self tuning, with VE maps, and a billion compensations...   Though then there's me over here when I'm doing reverse engineering work just reading data in hex format that most people couldn't work anything out from. Yet I can see what's going on.
    • Um. No. Since Matt introduced the TIM it has become a lot easier to deal with the consequences of changing K for AFM and injector swaps. Then, tuning is a f**king doddle. No-one needs to know or care how many grams of air are flowing or any other bullshit. Need more fuel in a cell? Add more fuel. Need more timing in a cell. Add more timing. Need to adjust any of the other tables for warm up and so on? No harder than anything else. Sure - it's not an ECU system for starting from scratch on an arbitrary engine. But then.....it was never supposed to be, not recommended for, and almost never used that way. So.... On your engine, in particular, Nistune/Nissan OEM is about as sophisticated and difficult as banging 2 rocks together. Those ECUs are primitive and simple. There is nothing difficult there. I learnt Nistune from scratch, created new maps with extended axes, interpolated/extrapolated the original maps onto them and tuned my RB20 (basically the same ECU as your 26 ECU) all by myself, more than 20 years ago. And that was long before even TIM.
×
×
  • Create New...