Jump to content
SAU Community

Help Installing Powerfc

Nate79
 Share

Recommended Posts

Nate79 Enthusiast

Nate79

Posted
Posted

Hi All,

I just tried to install my new PowerFC into my R33 GTS-T. After removing the sock ECU I noticed the PowerFC doesnt have any screw holes to mount it in the existing brackets. Also the plugs for the hand controller are on the adjacent side to the wiring loom, so its completely covered by the top bracket. Has anyone else installed these themselves, I'd appreciate some advice. Do you have to get brackets made up? In the FAQ's they say to just replace the ECU with the PowerFC, didnt think I'd run into this much trouble. :D

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/119284-help-installing-powerfc/
Share on other sites
justin911 Grand Master

justin911

Posted
Posted

it should just slide into the stock bracket and sit pretty firmly.. i also used some double sided tape..

install it without the h/c connected and then just slap her in afterwards.. but ya it will take a while seems u cant realy see anything

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • wizlb
      2020 Nissan Skyline 400R V37/Infiniti Q50 RS insurance in NSW

      By wizlb · Posted

      If you have a Nissan from Japan and model year is from 2016 to 2024, just say you have an Infiniti Q50 4 doors... Why are telling you have an import?
    • GTSBoy
      Rb25det s1 igniter pin out

      By GTSBoy · Posted

      It's definitely not firing order. But I think it should also be made clear that the output that gets fired is the one that corresponds to the input that was switched at the ECU. So you could scramble them up totally so that the numbers meant nothing, and so long as you had the inputs and outputs matched up, you'd be fine. The reason I make that point is that blanket statements about what it is supposed to be don't always hold out in a world where there's been 30 years for the wiring to have been stuffed with.
    • EndZee
      Rb25det s1 igniter pin out

      By EndZee · Posted

      Hello, im asking about this guy - coil igniter on rb25det series 1 r33 s1 engine. I need to know if pins on coil side indicate coils itself from 1-6 or it’s firing order so pin nr1 goes to 1st fired spark plug:(1pin-1firing spark, 2pin-5order firing spark, 3-3, 4-6, 5-2, 6-4…)   photo: https://files.fm/f/k9pdug38uq
    • GTSBoy
      Powder coat on mating surface

      By GTSBoy · Posted

      Remove it. Certainly from the hub face. I'm not in love with leaving it on the wheel assembly surface either - but if it is common to do so, then....maybe fair enough. It's not difficult. Just time consuming. For the hub face you just need a large enough block and suitable grades of abrasive paper to get it off flat. The same would be true of the assembly face. Just more time consuming, probably needing a lot more care. It's defo going to be easier just to assemble the wheels as is, seal them up, and check them periodically to see if there's any movement or loosening of the fasteners, than it will be to remove it though.
    • dyl33
      Powder coat on mating surface

      By dyl33 · Posted

      Hello, I got my wheels powder coated and they've powder coated bloody everything the mating surface and hub (even told them not to lol) anyway should I leave it or remove it. (Would be very hard) I've searched a lot and lots of powder coaters don't mask the mating surface but do mask the hub surface. How bad it powder coat on the mating surface or hub? My question is what should I do?
×
×
  • Create New...