Jump to content
SAU Community

Recommended Posts

lunch will consist of any types of food i'd be able to digest easily.

so, food it is :happy:

You should be able to digest pureed food easily? :)

damm and i was so lookin forward to actually going out cruising tonight.

But Eddie was going for a run tonight...not a cruise :D

back :P

How was teh swimming?

But Eddie was going for a run tonight...not a cruise :happy:

i thought he was wanting to take his so called "girlfriends" fto out for a thrashing but his so called "girlfriend" wants to take the gtr out and he'll thrash that instead.

but then again, he wants to go for a run to the sunshine coast hey?

hrmm!

Is everyone going on the charity cruise?

:D:P:D:huh:

i dont know now....

i wasn't welcomed. i was at a stage as long as i stayed at the back of the pack but then that post was removed :)

now i dont know :happy:

i thought he was wanting to take his so called "girlfriends" fto out for a thrashing but his so called "girlfriend" wants to take the gtr out and he'll thrash that instead.

but then again, he wants to go for a run to the sunshine coast hey?

hrmm!

:happy: anyone else confused :D

:D:huh::(:(

i dont know now....

i wasn't welcomed. i was at a stage as long as i stayed at the back of the pack but then that post was removed :P

now i dont know :)

Yeh I understand how you feel...

PM ;)

John, ever thought to just move on and get over it? if you stop posting shit about him, then he will too (hopefully) then none of us have to read about your fighting.

Bryn you wont be depressed... I'll just drive you there and when we crusie you can drive just stay in the middle of the pack if a coppa stops everyone just jump out "to see whats the problem is" and then i'll jump out and say i was driving :happy:

ha ha ha

well I think Eddie is a Real Tool for coming on hear and having ago at John, they did take their fight to pms but then he still shows up here, and stirs trouble.... but i is a good read and fun too

well I think Eddie is a Real Tool for coming on hear and having ago at John, they did take their fight to pms but then he still shows up here, and stirs trouble.... but i is a good read and fun too

UMM, eddy took it to pm's and i ignored them forwarding the pm's onto others for a laugh.

eddy though kept on pushin it in here to which made people laugh even more makin more of a fool of himself with the amount of bullshit he talks, spins and spun left, right and centre.

i agree with ya its good for a read and seriously, just goin along with his shit made things even more funnier!

has anyone here gone on the 1 point for a year thing? considering it was just a good behaviour adn license never gone, does it put my opens back a year or not?

no, you dont get put back a year for your opens.

you get your opens the day its due. instead of getting the 12 points, you actually get 11 instead.

this happen to me.

except, when i went on my 1 point, i sold my car and didnt have a car till i gained my opens.

best idea i ever had and did!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • This is lower price now given apparently nobody wants these or needs them. It's 550 but if someone sees it on SAU and wants to make an offer, please do so.
    • LS is a good motor, but it hurts my soul when I see it in a RB. Guess it fixes the oiling issues lol.
    • I'm confused. Does this qualify as "Gregging" or are you somehow avoiding the Gregging?
    • More assembly going on, with all sorts of "bolt right on bro" scenarios going on here. Smartly, PTV clearance was checked. And I say smartly because it turns out that the intake was 0.009" from piston meeting valve. This is 0.23mm. This is very not okay. A fast meeting was facilitated between engine builder in Australia and engine builder in the USA which was actually incredibly helpful and constructive actually, various ideas thrown around to get around this issue including: 1) Retard the cam timing which would have brought the exhaust valve closer to meeting piston (it was 0.065") which was uncomfortably close to begin with, and change the cam profile making it 'laggier' 2) Much larger head gaskets which would reduce compression, but half the point of this was to increase compression. 3) New set of pistons ($$$$$$$$$$$$$$$$$) 4) All of the above 5) Get ghetto The concept is you get sticky sandpaper and stick it back to a valve, slightly larger than the valve you/I'm using, like say from a LS3/rectangle port head. You now have a very super advanced flycutting tool to modify your pistons in your block. Then you install it in your head, and attach the other end of the head to a drill. Then you just replicate your valve smashing into a piston with your spinning drill.   This is the result. Repeat many times. It is strongly recommended you have some kind of fixed stop when doing this for extremely obvious reasons because if you press too hard then you're well into apocalyptic repercussion land. The minimum clearance on the intake valve is now 0.075" this is still in the "Too close to be really comfortable" and into "It should be fine" land. Supposedly in the real world the clearances will be slightly bigger. Guess this is what happens when people push envelopes for N/A engines instead of adding boost! Time to move onto the new, upgraded, higher ratio roller rockers from Yellaterra, all tapped and threaded with a stronger bolt for better stability. Very nice. Lets see how they fit. For f**ks sake. Time to bring the grinder out for these aftermarket, machined and CNC'd heads. Looks like the new, beefier rocker from YellaTerra has gone from Bolt on part to "Bolt on part". Well, lets see how this bolt on crank scraper and windage tray goes then, shall we? There actually is more clearance than they specify for this thing, but seeing it all move as you check it is terrifying when you see it all so very very very very nearly hit things. But after all, this is what the item is designed to do after all and actually did bolt on perfectly and have enough clearance to everything and some very clear and direct instructions. So +1 to Improved Racing I suppose. As above with the windage tray on. Photo of breaker bar wonkiness for added lols. Next up: Oil pump/front cover/water pump/sump and then it's time to actually install the heads, pushrods, head bolts, valve cover gaskets and such is all there and ready to go. (except the oil pump bolts which were previously longer for more clearance with the previously perfectly installed double row timing chain). There's definitely a sense that someone other than us has been here before and done everything perfectly, or at least considered it and came up with working solutions. Perhaps the previous cam was 6deg advanced to avoid PTV issues with the milled stock heads? In any case when I attempt to sell this stuff the buyers are going to be very directly informed.
    • my catch can is pretty easy to empty but it overflows due to the blowby/crank case pressure etc. max I have drained is ~600ml even with a ~2.3L capacity. So it is not just about having to drain it out its the mess it makes down the firewall and under the car and rear passenger tyre from the overflow oil being blasted by screamer + air in general. Ending up on the ground cleaning the oil up and having oil on your arms when everyone else can chill and watch the other sessions gets old fast
×
×
  • Create New...