Jump to content
SAU Community

Recommended Posts

what you thinking of getting Bunta man..?
ur gay

incorrect. rb20 and 25 differentiate wiith bolt placement

i can post the imageshack link lol... but im not that much of a dick

looking for a chaser i hope..

go see iron chef imports.. he specialises in chaser

if all goes to plan it will be a white evo 8 MR i come up with lots of ideas but i always end up coming back to that

one 10mm bolt lines up differently.. dw bout it rohan dan will explain it to u

yeh 1 bolt is slotted on the later model rb pumps.

however teh pumps dan gets dont ahve this, and are exactly the same

if all goes to plan it will be a white evo 8 MR i come up with lots of ideas but i always end up coming back to that

panda or reverse panda. if not, dont talk to me.

yeh 1 bolt is slotted on the later model rb pumps.

however teh pumps dan gets dont ahve this, and are exactly the same

panda or reverse panda. if not, dont talk to me.

:D

good choice.. but chaser...:)

the chaser is too close in configeration to what I have now, and I would have to start all oaver again to make it fast...plus it has no brembos, brembos FTW

one 10mm bolt lines up differently.. dw bout it rohan dan will explain it to u

i know...and he did and i knew already....cause they are the same....one bolt hole that makes stuff all difference....they are not different black man.

yeh 1 bolt is slotted on the later model rb pumps.

however teh pumps dan gets dont ahve this, and are exactly the same

panda or reverse panda. if not, dont talk to me.

:D

HI EVERYBODY!!!!

:) git down bish!!1

sarp!!!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...