Jump to content
SAU Community

Whoretown - Now Interest Free


Squizz

Recommended Posts

ZOMG its Slide...in QLD :P

Hi Aaron >_<

hi

Im filling time because i dont want to go to the shop and make turbos today lol

going to queensland raceway tonight for test and tune so just relaxing :happy:

Link to comment
Share on other sites

hi

Im filling time because i dont want to go to the shop and make turbos today lol

going to queensland raceway tonight for test and tune so just relaxing :P

Show me how to make turbos. I need a new job :happy:>_<

Link to comment
Share on other sites

and slide if you have any tests done at PA hospital or QEII ask the info desk to page me after you finish and we can always catchup and have a starbucks :happy:

>_< im never in qld for hospital always sydney or john flynn

forgot the link in the pm

http://www.slidingperformance.com/catalog/...hp?cPath=51_117

Link to comment
Share on other sites

so do you take layby?

or even sexual favours for car parts....

just enquiring.......

Yeah i do layby

sexual favours is the preferred method of payment though lol

Show me how to make turbos. I need a new job :happy:>_<

hahahah ok

but i think the washing solution might eat through your virgin hands lol

Link to comment
Share on other sites

Quick Question!!

my mate has a r33 and there is a huge problem with it, it drives fine when not acelerating hard but when you give it 100% throttle it only revs to 4000rpm, wont rev harder, what could be the problem?

any of you guys free to come out on Thursday night to have a look at the car, its in the city?

Link to comment
Share on other sites

Yeah i do layby

sexual favours is the preferred method of payment though lol

hahahah ok

but i think the washing solution might eat through your virgin hands lol

How much bum sex for a new turbo? :happy:

and Anna has Virgin hands? >_<

Link to comment
Share on other sites

Quick Question!!

my mate has a r33 and there is a huge problem with it, it drives fine when not acelerating hard but when you give it 100% throttle it only revs to 4000rpm, wont rev harder, what could be the problem?

any of you guys free to come out on Thursday night to have a look at the car, its in the city?

if it sounds like its bouncing off the rev limiter i would say the air flow meter

if you know someone with the nissan data cable and software check for error codes

Link to comment
Share on other sites

lihn's back i take it and not givin u the needs hey?

:happy:

:P its just she spent all the money in Vietnam...

but i can still give out bum sex....

lol

and she does when it comes to chemicals that turn alloy into bubbles lol

just Anna and Virgin dont belong in the same sentence

Bubbles hey? where can i get this stuff? >_<

Link to comment
Share on other sites

if it sounds like its bouncing off the rev limiter i would say the air flow meter

if you know someone with the nissan data cable and software check for error codes

Why do you tempt me with your GT2860R-5 prices >_<

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I thought the problem with doing this is the engine needs more timing and therefore is actually less efficient? Modern engines need very little timing to get to MBT, those super sharp edges on the squish pads are probably not the right way to get there but doing away with it entirely doesn't sound right either.
    • this explains the possibility of several maps with different boost levels
    • ok, I understand much better how we can control the boost and increase the number of psi before opening the wastegate
    • Well.... yes and perhaps no. It depends on what you mean by "spool". For most of us, the point that we would describe as where the turbo is "spooling" is the point where the wheel speed gets high enough for it to start making some boost. This is coincidentally around about the point where it starts making noise - hence the "spooling" sound. If that is what you mean, then no - the wastegate should still be shut at this point. The boost will still be way below the point where it should start opening. If, on the other hand, you mean "spool" as "reach full boost", then yes. At the point where the boost has reached target, then boost control has already started. The wastegate is already open, and has been for some time. Some short time, definitely, but still, some time. If you have no boost controller - just the wastegate actuator connected to the boost source, then you have a mechanical system working as a pressure balance. There is pressure on one side of the wastegate actuator's diaphragm from the spring, and pressure on the other side coming from the boost measurement location (the "source"). This is not a digital thing. The wastegate does not stay shut until the boost pressure reaches the spring "pressure". The spring will start to compress as soon as you start to apply any pressure onto it. This can be controlled somewhat by adding pre-load into the spring, but you cannot add enough preload to make it into a digital switch behaviour. The wastegate will crack open and start to leak exhaust out (and therefore not though the turbine) well before you reach the target boost pressure. Electronic (and some mechanical/pneumatic) boost controllers will act to prevent the boost source applying pressure to the actuator until just before you reach target boost, thus preventing the wastegate from creeping open. And some boost controllers will apply boost pressure on the spring side to further push it shut. And this can be be necessary because the exhaust pressure in the manifold also pushes on the wastegate valve and tries to open it and you cab get it leaking even without it being connected to the boost source.
    • A stand alone boost controller will not give you the control you need, unlike a modern ECU. Your boost will always naturally target the wastegate's opening pressure first, your controller then will allow you to add more boost as required.
×
×
  • Create New...