Jump to content
SAU Community

Recommended Posts

ok

some S13 strut braces fit front - as some dont have the clearance and other designs do... but there are a31 specific ones...

rear strut bars - s13 wont fit as the screws in the camber tops are on a different angle.

BUT there are ones like the one in my car which are universal for S13 / A31 / 32... (basically just has 6 holes drilled in each strut plate thing. One on a left angle / other straight / other on right angle thing...

  • 2 months later...

Since you guys are on this subject.

Can someone tell me is there anyway to make the ride height higher if one is using the s13 coilovers on an a31?

I put in a set of s13 coilovers on my cefiro but I felt its sitting too low and won't get a lot of clearance on some roads/ramps/speed bumps. But the coilovers currently have been adjusted to the maximum height already!

Need help please....

Since you guys are on this subject.

Can someone tell me is there anyway to make the ride height higher if one is using the s13 coilovers on an a31?

I put in a set of s13 coilovers on my cefiro but I felt its sitting too low and won't get a lot of clearance on some roads/ramps/speed bumps. But the coilovers currently have been adjusted to the maximum height already!

Need help please....

There's another thread where this is discussed.... http://www.skylinesaustralia.com/forums/in...howtopic=145426

I have similar problems...

I reckon that being so low looks good, but I do have problems since I can't get over the speed-bump into my apartment complex without the car bottoming-out, and the last time I went to the drive-through carwash I got stuck!

here's the suggested fix in that thread..

if there as high as they will go and for some odd reason you want them higher you might want to try to locate a set of helper-springs.

Eibach%20helper.jpg

Helper springs made my ride height higher, but the more compressed rate of the springs made the back-end of my car extremely jumpy due to the extra spring-loading. I've decided to change my shocks soon.... but helper springs may help your case

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...