Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

new wheels 18x9 Xd9s

goodk.jpg

Uploaded with ImageShack.us

nice looks clean and roadworthy :) no issues from authorities,

but if u do decide to upgrade,

XD9' in;

17x9.5+17 with a 215/40 profile tire up front

18x10+38 with a 235/40 profile tire on the rear

fits perfectly on a R32 Gtst with rolled guards :)

my new toy.

building it for track work.

post-39965-0-43604800-1292634791_thumb.jpgpost-39965-0-51166800-1292634823_thumb.jpgpost-39965-0-60380700-1292634847_thumb.jpg

whats your thoughts on headlights tho??

im undecided.

the lights are definatly different. a mate of mine did the same thing about 4 years ago but recently got defected and had to put it back to stock.

i think if you made a perspex cover that had the same shape as the original headlight it would look good.

i particualy like the black door handles on the white. ive always loved black and white mix on a 32 thoe.

This is my 32 had it for about 5 years now its almost there done a 2jzgte conversion that been in there about 2 years getting ready to do a E85 tune hoping to get close to 550hp at the wheels

034.jpg

036.jpg

engine_bay.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welp, too late already committed to the cam cover breathers to be welded on. I did think about adding a catch can in line with the drivers side sump breather as a phase 2 along with a drain to the sump on the original catch can but with an inline ball valve so I can have it closed if needed.    Likely a single breather would have been enough but I think I’m overcompensating to hopefully not have to empty my catch can and clean up oil over flow every session.    out of curiosity has anyone actually measured crank case pressure before and after various mods? I’m considering adding a sensor for science 
    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
×
×
  • Create New...