Jump to content
SAU Community

I Learnt How To Drag Race On The Weekend.

Abo Bob
 Share

Recommended Posts

1JZ.747 Community Regular

1JZ.747

Posted
Posted
It was an auto only tip. Basically I had one foot on the brake and the other stalling it up but the tip was to use the handbrake as well so as to hold it stronger. Got about 150 extra rpm which got me about 5 psi boost off the line.

I also utilised previous 2rismo tips in doing 3rd gear burnouts. Tyres were nice and warmed up although a couple of times when the burnout wasn't quite as big I found out how far down the track the prep went. Top of 2nd gear wheel spins anyone? It doesn't even do that on the street with my shitty Falkans.

the old hand brake routine, yep been using that one for a while, helped my sixty foots emensly, though its time to tighten it up again.

ido09s Mentor

ido09s

Posted
Posted

nice one Adam!!!! its rather strange though how it takes so long to crack a decent time then once its been done once, it happens several times in a row.... happens to me every time :D:(

how do we find out about these private track hires though, i need some more practice now :):):):):)

Abo Bob Grand Master

Abo Bob

Posted
  • Author
Posted

I think it was a low 1.9 but I got a high 1.8 on another run but accidentally short changed 1st gear and made up for that blunder by hitting the rev limiter in 2nd giving a crap time instead of what it could have been.

If I had known you were keen I would have let you know Brad. There was a few spare spots. I'll pm you if I see something come up.

I keep forgetting to bring the timeslip in to work to scan.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Desean Strickland
      Need help/advice with bearing taper clearance, eccentricity and arp studs.

      By Desean Strickland · Posted

      Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • soviet_merlin
      Mistakes were made, my R34 Story

      By soviet_merlin · Posted

      Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...