Jump to content
SAU Community

Recommended Posts

Hey guys,

Kind of silly n00b question, but im stuck, where do i begin modding my car,

Essentially i want the car to slide well (drift), but do i start with power or handeling?

The car is completely stock bar the front strut bar and a pod, should i go for exhaust or coilovers?

Any suggestions?

Cheers

(sorry for the n00b question........)

Link to comment
https://www.sau.com.au/forums/topic/120054-4-door-r32-gts-t-mods/
Share on other sites

Good to hear. I have a 4 door gtst 32.

If you want to drift a good choice is the suspention. Coilovers all around.

front mont cooler and then you can up your boost a bit.

17" wheels are better than the standard for drift, they also look far better.

you also will need to lock/remove your HICAS (rear steering) because drifting will become hard with any speed.

Mal

Edited by wal

(sorry for the misplacement of topic.... may bad)

Thanks for the info, i was leaning toward suspension, i was planning on teins and a hicas lock kit, looks like that will be my next mod!

I guess in the early learning stages power isnt important its more about technique and set up.

Thanks man.

:(

Yeah mate if you're heading for drift a set of coilovers with 8kg front, 6kg rear spring rates. Pretty good balance for a daily driver.

Make sure to get a Hicas lock BAR. As some kits only add washers to the hicas mechanism.

If you can handle a bare boot> Strip it bare.. There's a good 20-30 kgs kg's in there.

After the suspension is sorted you should really look at a good mechanical LSD. But if the stocker is in reasonable nick you could probably get away with it for a few months(cause I know stock exhausts suck). If you're really cheap you can get it 'Shimmed up'. But they rarely last more than a year after that.

That was another question i was going to ask was spring rates, thanks Drift limo!

Shimming up the diff sounds like it will cost more in the long run, what are your guys opinions on KAAZ diffs???

The lock bar is def going in, hicas is annoying :D

Should i be installing sway bars with the coils and camber arms?

Cheers guys

I have a R32 sedan which I use to compete with in Perth. The basic mods I started off with was a catback exhaust, pod filter, hicas lock, front and rear strut braces and a set of coilovers. Which I found was more than enough to start drifting on. Since then I have added pineapples, GTR skyline rear swaybar (enables slightly more oversteer), a cheap spring type boost controller and a FMIC. If I had my time again I would spend the money on buying a decent FMIC kit, preferably one which has 'switchback' piping (comes in at the right and goes back the same way) because it will for one allow you to put in a decent size oil cooler in a convinent location and also avoid the heatsoak that the piping recieves through the crossover piping (which pretty much render's the FMIC pointless).

There is no need for 17" rims or tyres. I drift on stock GTS-T rims 205/55R16's front and rear with the rears sets set to 45 psi. However if you already have them good grip front tyres are definately a necessity. Before you go drifting on the track remove your rear seat and spare tyre and then you should be able to fit 4 rims with tyres in the area where the back seat was with ease.

Having more power always helps.. but its pretty pointless if you can't use it effectively due to lack of driver skill or suspension setup. Stock power with a catback exhaust and a pod is more than enough to start off with. Allows you to drift with your foot flat as well most of the time which makes it easier to drift on.

So in your position I would say lock the HICAS as a first priority then find some coilovers and then an exhaust. And this should be more than enough to get you started.

Oh yeah make sure your handbrake is adjusted properly as well.

Cheers,

Baz, this will sound wierd but ive sen you slide at wanneroo and your the reason i got a four door.

What youve just said makes mucha sense, looks like ill be doing that switchback idea too!

Thanks for the input guys, it will be put to good use!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean the other day I had to walk someone through diagnosing why their timing belt was walking off the cam gears. At least one of the issues was a bent tensioner stud. Local mechanics have found runout on the CAS mechanism causing weird failures. I'm also no saint here I've documented some of the things I've had to learn the hard way. Something I discovered recently is that my CA emissions catalytic converters weren't even welded correctly to align the downpipe to the main cat and they tossed the support bracket that goes from the transfer case to the downpipe to support everything there. I spend a lot of time chasing down these decidedly unsexy problems and the net effect is it feels like I never actually get to the original objective (flex fuel, VCAM, oil control, cooling, etc).
    • At times with how you make everything sound, all I imagine Americans doing when they see a gtr is standing there looking at it and bashing it with a gun like how a caveman would with a club and hoping it fixes itself 
    • I think this is just a product of how the US market works for this stuff. Shops are expensive and there's no real way of knowing what kind of results you're going to get, people don't really have the institutional knowledge. I have heard too much at this point to really put faith in anybody "full service" except maybe DSport and they aren't really a full service kind of shop. If you go to the right place I have no doubt they'll get it right for you. Some locals have set it up right but the cost really is nuts and even now they're still fighting issues. And you know I'm a crazy person who thinks things like twin scroll, relatively short low-mount cast headers, PCV recirc to intake, recirculating BOV, right-sized for ~400 whp, MAF load, validating all of that to a standard comparable to OEM test programs, etc are relevant. For what it's worth, multiple local owners at this point have been stuck in a perpetual cycle of blowing a motor -> getting someone to rebuild it -> some missed detail causes the bearings to wipe and spin just outside of break-in mileage or drop valves or some other catastrophe -> cycle repeats. I usually only find out about this because I'm perpetually helping random friends with diagnosing car troubles, Skyline or otherwise. The single turbo stuff if I'm honest is mostly secondary, it just doesn't seem to achieve the numbers in the ~2000-3000 rpm region that I would expect given the results I've seen here or in Motive's videos. I don't really know what we're missing here in the US to be causing this. Lots of people like to emphasize the necessity of finishing the project first and foremost, but I'm not made of money and I can't afford to be trashing a 15k+ USD engine build with any regularity. Or spending my relatively limited garage time these days unable to triangulate problems because too much was changed all at once. Also, even if it isn't a catastrophic failure I would consider spending the cost of single turbo conversion with nothing to show for it to be pretty bad. 
    • The water pump is know to leak as well. So if the coolant is low checking that first as well as hoses. 
    • Reading your posts Josh, sometimes I feel like I've gone in a time machine back to the 90's when everyone was doe-eyed and figuring things out for the first time.  I've lost track of how many single turbo GTR's I've seen on track that haven't burnt down lol. Everything has been figured out a long time ago. These things are at the point now where its essentially turn-key to go single turbo. 
×
×
  • Create New...