Jump to content
SAU Community

Recommended Posts

Im just wondering when the time comes when you have to change your engine for one in better condition how can you make sure your getting something which is in good nick and is not just a thrashed item?? Are there any hints or things that should be looked at and done before purchasing a engine?? also what would be a reasonable amount to pay to recondition/rebuild a RB25DET back to its beautiful factory brand new condition??

Edited by LatinR33

looking at minimum $3000 for someone else to do the rebuild

just new pumps, rings and bearings.

-- hard to tell about engines unless they are still in a car, could try a comp test on a engine not in a car, but yeah, would be very hard lol

it wouldnt be THAT hard, just a bit of a prick. just remove all the spark plugs except the cylinder you're testing. get a 27mm socket on a rachet. then turn the bolt thats holding your harmonic balancer in... that'll give you a compression reading. anything above 160 is pretty good, and make sure all cylinders are within 3% (i think) of each others readings.

other than that have a look for water leaks around the block and water pump and general oil leaks around the motor.

anyone who sells you a motor gives you some kind of warranty of around 3 months so just make sure its in the car before 3 months and send it to a mechanic to get checked thoroughly.

it wouldnt be THAT hard, just a bit of a prick. just remove all the spark plugs except the cylinder you're testing. get a 27mm socket on a rachet. then turn the bolt thats holding your harmonic balancer in... that'll give you a compression reading. anything above 160 is pretty good, and make sure all cylinders are within 3% (i think) of each others readings.

other than that have a look for water leaks around the block and water pump and general oil leaks around the motor.

anyone who sells you a motor gives you some kind of warranty of around 3 months so just make sure its in the car before 3 months and send it to a mechanic to get checked thoroughly.

have to disagree Joe.

you cannot spin the engine fast enough in this fashion.

the strength of the battery affects the speed of the starter motor when doing it in a car, which affects the results. most test results are between 100-200 rpm

the rings dont seal nearly good enough to seal at hand turning speed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
    • Just putting it out there, that's a decent list. You would be better off *not* doing *any* of that and buying someone else's modded car. Like mine. Or anybody else's. Yes it's lotto dependent and all this and that but that 70K (remember, double your guesses) could go elsewhere. Keep it stock, save your money, go lowball @Dose Pipe Sutututu :p
    • Does not mean what you think it means. The continual rising coefficient is the coefficient of friction that continues to rise with increasing temperature. Not "rising during a single stop", except inasmuch as the brakes should get hotter during a single stop. The RR would not be the best choice for a streeter. Yeah....no it's not. JAX would rummage around in the "shit pads we use for all shitboxen that come in here" and install those.
×
×
  • Create New...