Jump to content
SAU Community

Recommended Posts

for the wheels... well im looking at the model 5 copies on uniqueautosport website that are $1180 then buying second hand tyres. so they would have to work out less than that cause i prefer the model 5 to vs-5 (or whatever your model is called) even if they are copies.

thats what i was planning to do, by a standard bar and hack into it to fit the fmic. more stealth than the big trust bar.

040 goes in factory location - in tank,

If you are serious about wanting parts, then PM me your offers, but parts wont go cheaply as my preference is to sell the car complete, unless i find a buyer to buy my car less bits.

Thats not to say ill be asking for new part prices, but say i wont accept $500 for rims, of $600 etc for intercooler.

It is a Type S intercooler, from memory 600 x 300 x 60mm (or 76 check their website)

It came with HKS piping and hose/clamps, to look at the material is powder coated mild steel.

As for condition as i run mesh on my front bar it is in great condition, after a quick dip in some caustic to clean it up it would look like new, ie not a bent fin on the cooler, not one!

I dont have an oil/air separator so MAY have a thin film of oil on the inside that will clean up easy with the caustic bath.

Will try to take some more pics over the weekend, including interior, engine bay, suspension etc.

So just to clarify for those people who have sent me PM for parts, there is a couple of people kinda interested in the car with filter, zorst, brakes/susp.

If they take it off my hands then i will then be selling the IC, AVC-R, Power FC, oil cooler, Bosch Fuel pump etc AFTER the car is sold.

As i have explained to people i dont want to sell off good bits and be left with stocka that i have to drive every day, or no one wants, so have to sell cheaply like Chef _32's friend.

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah it factory manual not sure about ratio but it looks like there’s been some work at the rear 
    • so I need a new speedo cable 
    • Throwing my spoon to the soup here a bit.  When I installed a 044 back in 2012, along with the direct power mod, the car became very difficult to start. To a point I burned one starter motor as I was late for work and tried to get the thing going. With some tuning and careful use of gas pedal when cranking it became bearable. Trying to make this short as possible, but the 044 died after 2-3 years, after which I went with an AEM 320lph pump, which also died after about 4 years to my dismay. After that I went with a Nismo pump, and while trying diagnose an emissions problem, I noticed for the first time that my fuel pressure was 5bar/72psi on idle, and that removing the vacuum line did nothing. After monitoring the situation, and removing the direct power feed and going back to FPCM in attempts to remedy it, I noticed there was fuel in the pressure regulator vac line. Kept the FPCM, installed AEM external regu and the car became sooo much better in every way, including starting. And I had driven it like it was for 11 years.. Anyway, I agree these are likely two different problems, and the FP problem you just haven't noticed before. I do not know much about haltecs, but what first came to mind was the CAS, which probably is not there any more. So how is the wiring from haltec to gauge cluster? How is the battery voltage and alternator?
    • Your car was auto before? You have different diff ratio (auto vs manual i think? or n/a and turbo?)
    • +1 for getting a screen off alibaba, CarPlay/Android Auto is vastly better than whatever navigation cars had 10 years ago. I got an Android screen for my 2015 BMW, huge difference. Fully compatible with factory stuff including iDrive controls.
×
×
  • Create New...