Jump to content
SAU Community

Recommended Posts

Here's a little write up on how to install a boost gauge into the drivers side vent of an R32.

post-10239-1150443012.jpg

*disclaimer: If anything goes wrong or you break anything while following this post it's not my fault.

Items needed:

Phillips head screw driver

Socket Set

Spare vacuum line (the thin stuff that just fits the clear autometer tube inside it)

plastic T piece that fits the above vacuum line

Masking tape

Step 1

IMPORTANT Open the bonnet. It's easier to now than it is later

Remove the dash piece that's above the pedals and below the steering wheel.

- there are 4 screws along the top side

- 2 screws along the bottom side (32 gtst)

- 1 screw at the side (covered by the door when it's closed)

- 2 bolts that also hold in the bonnet release

n.b. Unplug the beeper after you've unscrewed everything (you'll see it when you do it)

Step 2

Once you've removed this piece you'll notice that the vent is attached. Unscrew the two screws holding it in and remove.

Step 3

Now what you'll notice is that you've got a nice little hole where you should be able to fit your gauge. Some fit, but with the autometer boost gauge that we had there was no chance of getting it in.

If this happens you need a Dremel. If you don't know what a Dremel is, maybe you should get someone that does and have them finish the install :(

Ok, now if you check the packaging that came with your autometer gauge you should notice that it came with a circular tube of hard cardboard in which it was placed. Get this tube and use it to see how much of the hole you need to widen.

Now with the autometer gauge I was lucky cause I basically just needed to shave off the clean rounded edge around the hole.

There was a lot to take off regardless. It's just this edge gave me something to work towards so that I kept the hole round, and didn't go too far.

Step 4

Dremel time.

I used this attachment.

post-10239-1150444255.jpg

Now here's where I wish I had taken more photos.

I didn't use this attachment to cut into the hole, I used it kinda like you would sand paper. Shaving away this inside of the hole slowly. TAKE YOUR TIME. Do NOT hack away at the hole, just shave the edges down slowly, moving around the hole till it's bigger.

Eventually it'll be big enough. Keep checking.

Step 5

Insert the gauge.

post-10239-1150443245.jpg

Here you can see the snug fit. It was actually so snug I couldn't get it back out again. So make sure you've lined it up properly before you push it all the way in.

Step 6

How the hell do you get the vacuum feed from the engine to the gauge??

Have a look in the engine bay.

post-10239-1150443392.jpg

The vacuum line highlighted by the red arrow is what we need to cut.

It currently feeds the stock boost gauge controller (the little box on the left).

Now look to the left a bit more and you'll see a hole.

post-10239-1150443315.jpg

This is your entrance into the cars cabin.

Here's the other side of that hole.

post-10239-1150443100.jpg

...and a bit closer. (Note I've already pushed the clear autometer tubing through the hole)

post-10239-1150443173.jpg

Step 7

Feeding the line.

- Grab an old coat hanger.

- Unwind it.

- Grab the clear autometer tubing.

- Line up the end of the tubing with one of the ends of the coat hanger wire.

- Tape around the end of the tubing and the wire tightly... make the end smooth and one piece basically.

- Get in the car.

- You see this rubber stuff?

post-10239-1150443173.jpg

- Poke a hole through it, then shove the coat hanger plus tube (taped end first) in through here.

- Now go and have a look in the engine bay.

- You should see the coat hanger and the tube in here.

post-10239-1150443315.jpg

- Grab it and pull it through.

Now that wasn't hard was it? Few mins and your done. So many people told me this step would take forever and was a bitch... sif.

Step 8

Attaching the Tpiece.

Cut the vacuum line pictured.

post-10239-1150443392.jpg

And attach the Tpiece.

Then cut the clear tube to size....

post-10239-1150443464.jpg

All done for the engine bay.

Step 9

Connecting the vacuum line to the gauge.

N.b. Ensure you leave enough slack in the vacuum line to get the gauge plus dash piece out again once installed.

Basically follow the instructions for you gauge at this point.

With autometer gauges, be careful not to twist or bend the clear tubing when screwing the attachment onto the gauge.

Step 10

Making it light up.

Grab the 12v feed from your cigarette lighter. It's the easiest 12v wire that goes "hot" when the headlights are turned on to find.

post-10239-1150443529.jpg

Wire this up as you would anything else. If you don't know how to do this, you shouldn't be installing the gauge.

Step 11

Admire your work.

post-10239-1150442922.jpg

post-10239-1150443012.jpg

Link to comment
https://www.sau.com.au/forums/topic/122508-r32-boost-gauge-install/
Share on other sites

very nice man, a great write up, sucks u didnt do it 2 weeks ago woulda saved me some time. But what did u do to stop the hot air blowing into the back of your gauge?

Gaffa tape ;)

Hey it works, and you can't see it :P

But shhh. It's my g/f's car and she doesn't know I did the dodgey and used gaffa to seal up the vent. lol :)

  • 10 months later...
PROBLEM

For some reason on the aftermarket gauge, it's says im pushing 11 psi ... Why?

The car is not boosted, according to the stock guage it's reading 5-6 psi

Is the aftermarket gauge reading doubling?

stock gauge does not read PSI. It reads a different unit hence why its maximum is 7.

Stock r32 does 10psi standard. A larger exhaust/intercooler will cause boost leak and hence the 11psi read.

Please save questions like these outside the tutorial section :whistling:

  • 10 months later...
  • 2 weeks later...
  • 2 weeks later...

Even better if you have an APEX'i EL series gauge (60mm) as they fit in perfectly - no cutting/boring!

Just need to secure it from the back (ziptie etc) and its apples!

CLICK ME

I bought one of those EL2 gauge's after reading this and it fits in perfect! Just needed a bit of tape around it and it fits/looks awesome =] Old one i had in there had like layers and layers of duct tape looked horrible..

  • 4 months later...
  • 1 year later...
  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It really depends on your setup. Mine is 'accidently' more suited to revving higher. bigger cams, turbo etc. Plus my super long first takes donkey years to come onto boost, so if it will move my power band to the right, maybe i'll pass on this. i have a G45-1500 going on there soon which I suspect might make it more of a fat pig.
    • Yeah good call, I will endeavour to tuck that down when I rewrap the looms it’s pushed up by
    • Good work. I will say, this line circled however, will potentially pool with oil, as it's going from high, to low, to high, before heading downwards.
    • Yeah, thumbsup from me. The distant shot of the bay just looks same-same as before.
    • Dad had a court case drag out with them from 1998 to 2004. He was in a not at fault accident, NRMA were the ones who covered the other person. They tried to blame his neck injuries on the fact he'd had an injury in 1981 on his extreme lower back where he slipped a single disc right near the bottom. Had been all cleared from that injury for years. This accident destroyed his shoulder, and f**ked a heap of discs in his neck, and he still has major problems with it to this day. Sarah's sister while on her L plates had a small Suzuki Alto, she had stopped to give way to an ambulance, and someone changed lanes behind her because there lane was also slowing, and rear ended her at 80km/h. (She had been stopped for a few seconds already too!). Car was completely f**kED. NRMA sent the vehicle around to 3 different workshops as they kept claiming "We believe it can be repaired, and not written off, we just need to find the correct workshop". It took 3 months, and a lot of arguing before they'd concede and wrote it and paid out. About two years later her sister had a Lancer, someone pulled out of a stop sign without stopping (in an 80 zone). Her sister swerved, hit the front of the other persons car (Instead of dead t-boning the drivers door), which ramped her Lancer, and made it roll multiple times down the road. It hit every panel on the way through. Her sister had slid her self out of the car, and remembers the ambos walking to the accident (They'd been sitting at a set of lights just down the road and witnessed it) and they were saying "Well, this ones going to be a fatality, no way you can walk away from that". Well, she did. And then NRMA sent two assessors out to look at the car, both of which wrote it off. They tried to send another assessor out, except a HUGE uproar was raised, and they FINALLY paid it out. That was on a car, that had damage to EVERY panel, you could see from 100m away the whole car was also twisted, roof bowed etc. Nah, we'll try get out of needing to payout on a $10,000 car... Her sister ended up with major shoulder reconstructive surgery being required, and was permanently limited in her ability to do her job as a nurse after that, as she can't (And was told before surgery too this would be guaranteed to happen) regain full strength in that shoulder. However, there was no choice to not have it, as she could barely use her arm, which was her dominant one, and was in near constant major pain. (And she's the type of person that would try and walk off a broken leg!) NRMA did the biggest run around on the personal injury side too for about 18 months, even to the point of trying to put 100% blame of the accident on Sarah's sister, even though the other driver admitted she didn't look, and didn't stop, and was charged by the police. Sarah used to have a Barina insured with them. It was a policy setup, paid all 12 months in advance. At the end of the 12 months, Sarah was living with me, I reviewed the renewal, it clearly stated "If you do nothing, your policy will cease on XYZ date". We did nothing, as we moved her insurance in with all of mine and I was with Shannons. We find out 10 months later, NRMA decided, because he DAD had a car insurance policy at the same address as what Sarah's mailing address was (Garaged address had been changed), that they'd put Sarah's (What should have been non existent policy) onto her Dad's month to month charges on his credit card. We had to jump through hoops, to get a refund. They didn't care that we actually found the letter that said "If you do nothing, your policy will cease" they made us prove we had NON COMPULSORY insurance else where before they'd issue the refund, and after they agreed to the refund, it still took another 6 weeks and 3 more phone calls for them to actually process it. They also had two insurance claims from storm damage, and they were an absolute cluster to get resolved as well (one vehicle, one house). Some how, up until about 3 years ago, her parents were still loyal to NRMA too, and we were like "How the hell are you so loyal to staying with them, when other places are so much cheaper, and they've f**ked you over every time you've ever had to make a claim?"
×
×
  • Create New...