Jump to content
SAU Community

Recommended Posts

OK, for the 32, i'm after a set of side skirts, color isnt an issue.

For the r33, need passenger door, no dints, prefer maroon-

Boot lining, (Battery cover and floor section)

plastic panel under the steering column,

trim that goes up the outside of the "A" pillar,

Floor mats, "prefer whole carpet if available"

Good dash pad if any are available.

Also still after a rb25 compressor outlet elbow

Prefer Sydney.

Thanks

Edited by kjb_r33
OK, for the 32, i'm after a set of side skirts, color isnt an issue.

For the r33, need passenger door, no dints, prefer maroon-

Boot lining, (Battery cover and floor section)

plastic panel under the steering column,

trim that goes up the outside of the "A" pillar,

Floor mats, "prefer whole carpet if available"

Good dash pad if any are available.

Also still after a rb25 compressor outlet elbow

Prefer Sydney.

Thanks

HAVE ELBOW AND GTR SIDE SKIRTS EDD 0419204275 SYD

HAVE ELBOW AND GTR SIDE SKIRTS EDD 0419204275 SYD

Thanks to Edd, elbow is taken care of, as is the boot lining Thanks Aaron

Edited by kjb_r33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hmmm, what do you mean by getting weaker? And where did you get that test done? I've been wondering about my battery because the cold starts crank super slowly. The voltage is fine. Not sure if cranking amps can be checked at home. Battery is 4+ years old.
    • No. The simplest wastegate hookup, with no solenoid or other form of "boost control" (ie, control over your boost control, if you know what I mean) is a single hose, direct from the turbo outlet/hot pipe, straight and only to the wastegate actuator. It is that pressure signal that drives the wastegate to open, providing the boost control (and by "boost control" here, I mean, limiting how high it can go, which is essentially the spring pressure of the actuator). You only end up with tee pieces and alternate flow paths once you start adding things to the boost control system to allow you to determine how much of that boost signal makes it to the actuator. There are so many ways to do that that there is no single way to run the hoses and tees and the like. If you have a stock boost solenoid, then all it does is either allow all the boost signal to go to the actuator, or open up to allow some of it to bleed off. There needs to be a restriction in that bleeder to allow only a small amount to bleed off. And in a stock system, that would then be plumbed back to the turbo inlet (for "emissions control" reasons). That is actually what that nipple on your BOV return pipe could/would be for. If you have an aftermarket boost controller and solenoid, then the above is mostly true, but there is no need for a restrictor in the bleed, because the solenoid is pulse width modulated to create a variable bleed off. The air that escapes from the bleed can either be vented, or also returned to the turbo inlet. For emissions reasons it should be returned to inlet, but the amount of air being vented is so small that it really doesn't matter (either from an emissions perspective, or from an air-fuel ratio affecting perspective).
    • And other times you just need to go buy bigger injectors?
    • Yup. I actually just blew my turbo. LOL.  should have checked this thread before today. i also have no boost solenoid. so it should be...one line from wastegate to turbo inlet, and a T somewhere in that line that connects to the wastegate return pipe?
    • It's recommended, however I can assure you a good amount of people don't bother. FWIW, the OEM battery lasted 4.5 years and I changed it prematurely too, I reckon could have stretched it to 5 years.
×
×
  • Create New...