Jump to content
SAU Community

Recommended Posts

You all know I am not up with all the technical terminology, so I will state it simply. In wet weather my backend is all over the road. This happens whenever I take off from traffic lights, and when I turn corners.

It is not just that I am a bad driver (I hope) I am only going to 1500 revs to take off, as I am particularly careful in wet weather.

Could anyone give me some tips to stop this, and I wanted to know if a good set of tyres would help at all. The tyres on it are only six months old, so I wondered if I could just get good tyres for the back. If it will stop my backend from sliding, I would be happy to spend up to $300 per tyre (only for the back).

Link to comment
https://www.sau.com.au/forums/topic/12288-tyres-1994-r33-gts-t/
Share on other sites

angel,

You need some Diff cradle bushes. Whiteline suspension does the kit part number KCA349.

This kit installed in the traction position will give a better chassis transfer of power.

You will find cars that have suspension set too low or hard at the front suffer badly from traction issues also.

As for tyres,

The good old simex brand are fab for the price. Get a 225 or 235/55 for the back ( a fairly tall profile for good sidewall flex at the drags). Don't buy the simex tyres for the front tho' they radial roll too much.

My little 205/55 simex tyres got me a 13.4 second 1/4 so they are not a bad pick.

the kit cost less than $120.

Takes 10 to 20min to install. I did mine by myself with a big iron bar and almost crushed my fingers into jam but, an ordinary two person team can do it with a minimum of fuss and no danger at all.

Bat the eyelids at some of the perth boys to give you a hand, if that doesn't work then offer free beer. Or do both. You might want to make sure that the helpers have done the install before having said that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Recaro sr3 I've always found comfy, compared to my stock r33 gtst and bride fixed back.  Can get them cheapish from a Honda owner.
    • Does your rb gearbox have the common input shaft bearing sound? (One one where it goes away when u push the clutch in or get to higher revs) I heard if you put the wrong oil it can get this sound.
    • There's more than one way to skin that cat, and most of the sump Maatouks have done will be GTR sumps. They are HUGE in GTR drag racing here.
    • Yeah...I always start at the shift solenoids, because there's only a few reasons these will spook into limp mode, and bad shift solenoids is one ~ the other can be the shift control module (if you have steering wheel shift buttons)...it's easier to eliminate the solenoids first.
    • Might piggy back off this thread since there's been a good discussion about PWM.   I purchased a Walbro 460 F90000267 and have been looking into PWM to understand it. It was purchased more of a future proof as my original OEM fuel pump died (r33 below 200kw) and figured I'd just upgrade it to this. That's when it hit me that a pump this big can cause more dramas with such high amperage draw and heating of the fuel pump being on 100% all the time in such a mild setup.   I have a Nexus R3 and slowly collecting power mods but I was looking into the PWM feature on the NSP software:   Then looking at the graph from the fuel pump:     Am I safe to assume reducing duty cycle to 50% for example would make the pump run like a 230/lph ? Where does the PWM come in all of this ?   I've gone down the rabbit hole of PWM fuel pumps and it seems there are many differing opinions on how to go about it 😅  
×
×
  • Create New...