Jump to content
SAU Community

Intermittant 4wd & A-lsd Check Light In Gtr34 V-spec

GTR34-Vspec
 Share

Recommended Posts

GTR34-Vspec Apprentice

GTR34-Vspec

Posted
Posted

Hi all,

After reading most of your nice advices about the 4wd check light problems in the gtr32s to help to solve mine (gtr34 v-spec), unlucky nothing seems nere. Here is the problem that I've been noticing:

Usuallly, when it's cool (ambient temperature/left overnight), it ocurred less often. Sometimes, just started the engine for awhile, the 4WD and A-LSD check light came on at the same time either on stationay (while idling) or rolling on a constant speed. Tried to turn the engine off/on, the check lights went off and came back on after awhile. How come, these two check lights came on together??

I've checked the fuses in the egine bay + driver's kick panel, fluid level, the relay to the fluid pump motor. They are all fine. One thing I haven't checked is the pump motor cause I wasn't sure how to.

I had an advice that, have a ATTESA computer diagnostic test, but I'd love to sort the problem out with your advices if it's possible before bring the car to a mechanic.

So please advice me how to solve this problem, THANKS GUYS !!!

Duncan Grand Master

Duncan

Posted
Posted

well I've not had a look at the 34 computer, have a look at it (in the boot under the parcel shelf). when the 4wd light is on there will be an LED flashign a code number. Check the code number to the list of error messages in the 32 GTR workshop manual.

All on the assumption it works the same as a 32, my guess is the computer will still show error codes to help with problems like this.

All the other solutions like fluid, bleeding etc won't really help if the 4wd light is on. Most likely cause is a poor earth / bad voltage somewhere for intermittent problems like this.

GTR34-Vspec Apprentice

GTR34-Vspec

Posted
  • Author
Posted

Thanks Duncan,

I think you're right about the wirings. Yesterday, when it was in good condition, I tried to shake the wire loom near the pump => the check light poped up => turn off the engine => shake again => turn on => check light was gone. So, very high chance it's somewhere there. I'll strip it down on the weekend and I'll update to you later.

Cheers!!!

GTR34-Vspec Apprentice

GTR34-Vspec

Posted
  • Author
Posted

Hey guys !!

I've found where the intermittant bastard is !!! The water and corrosion contaminated on the connector of the fluid pump side. The voltage got leaked and shorted intermittantly caused the 4wd and

a-lsd check light came up. Just disassemble the connectors to clean the corrosion => DONE => THE GOZILLA IS HEALTHY AGAIN !!!

CHEERS!!!

  • 3 years later...
Nosure Proficient

Nosure

Posted
Posted
Hey guys !!

I've found where the intermittant bastard is !!! The water and corrosion contaminated on the connector of the fluid pump side. The voltage got leaked and shorted intermittantly caused the 4wd and

a-lsd check light came up. Just disassemble the connectors to clean the corrosion => DONE => THE GOZILLA IS HEALTHY AGAIN !!!

CHEERS!!!

Hi mate I got a same problem as you. can you point out where is the connector??? front?? in the boot??

Duncan Grand Master

Duncan

Posted
Posted

you don't really want to know....there are orange and grey connectors on top of the attessa pump. which is on top of the diff. don't think you will have much luck getting to it without dropping the subframe.

Nosure Proficient

Nosure

Posted
Posted
you don't really want to know....there are orange and grey connectors on top of the attessa pump. which is on top of the diff. don't think you will have much luck getting to it without dropping the subframe.

thanks mate, so how long it will take if let workshop do it?

Nosure Proficient

Nosure

Posted
Posted
you don't really want to know....there are orange and grey connectors on top of the attessa pump. which is on top of the diff. don't think you will have much luck getting to it without dropping the subframe.

I found the pump is just under the right rear of the car i clean and replug it. the light not come up for 15kms so far. so maybe fixed.

Duncan Grand Master

Duncan

Posted
Posted

sorry not sure how long it would take a workshop with a hoist.....would take me an hour to drop the subframe and 1/2 to raise it again but that has been on and off a few times.

definately a job to get someone else to do :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • njdgomez23
      How to fix centre console latch.

      By njdgomez23 · Posted

      After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • marni
      I need more than help to finish my R33

      By marni · Posted

      Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • r32-25t
      Attesa pump mount options / ideas? R32 gtr style.

      By r32-25t · Posted

      From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      Have you looked at the workshop manual?
    • GTSBoy
      rb25 gearbox mount options - solid mount?

      By GTSBoy · Posted

      Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...