Jump to content
SAU Community

Need Part Number For Plugs

RedDrifter

By RedDrifter,
in Engines & Forced Induction

 Share

Recommended Posts

RedDrifter Experienced

RedDrifter

Posted
Posted

All I need is the part number for the NGK 0.8mm gapped plugs for the Rb20DET

As its time for replacing the plugs once more.

I know this has been asked eleventy billion times and all but I have done the search and cannot find what I am after. :)

Thanx guys.

Link to comment
https://www.sau.com.au/forums/topic/123624-need-part-number-for-plugs/
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

Then you are not searching hard enough.

Go to the NGK website and you can select your vehicle there. The standard plugs can be re-gapped to 0.8 so don't bother fiddling around with a plug that's already gapped at that. Just be gentle while regapping them so as you don't chip the iridium or platinum tip. You go for standard plugs but remember to change them every service.

Cubes Grand Master

Cubes

Posted
Posted

Motor traders/Coventry's keep the BCPR6E, they are a 0.8mm v-power plug.

Last time I bought a set 6 totalled to ~$17. I usually keep them in for up to 30,000km's, by then they are pretty well stuffed but not affecting the cars performance in a seat of the pance way.

Up from there depending on the power being made the only option is BKR7E, they are a tad harder to get, here in Adelaide Motor Mates keep them, but for $4 per plug. :)

Be sure to shop around as supercrap were extremely expensive for the copper bcpr6e plugs. Complete joke really.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      George's R33 GTST build

      By The Bogan · Posted

      I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • shortyboy
      Drive By Wire Conversion options

      By shortyboy · Posted

      Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • pogman
      George's R33 GTST build

      By pogman · Posted

      small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...