Jump to content
SAU Community

Recommended Posts

This is mine just bought it and I got to drive it once so far until i register it. I have to sell my old 94 Cresta Tourer V before i can register this one. At least I got to drive it for a couple of hours, and it drives awesome.

1020949-1.jpg

1020949-2.jpg

1020949-6.jpg

this is my S1, have done manual conversion, greddy plenum, 80mm hypertune trottle body, FMIC, nismo fuel pump, nismo FPR, S15 inj, R34 turbo, Apexi PFC, R34 gtt brake upgrade, GAB coilovers. (PFC, FPR & INJ fitted after photo's taken)

Will be getting rid of front spoiler as have Autech bar to go on.

post-49281-1242466115_thumb.jpg

post-49281-1242466181_thumb.jpg

post-49281-1242466247_thumb.jpg

post-49281-1242466323_thumb.jpg

post-49281-1242466402_thumb.jpg

post-49281-1242466454_thumb.jpg

post-49281-1242466514_thumb.jpg

post-49281-1242466564_thumb.jpg

post-49281-1242466624_thumb.jpg

Took some pics of the car today. Shall have a full kit to in a few weeks and a few other mods and be lowered with a nice set of rims in the next month. So will upload more pics once all done.

Nice stag and a great choice of scenery :(

Went for a Tambo run and also along The Panorama after finishing fuel filter and spark plugs. Car definitely is running smoother. Pity there was so much traffic out today....

post-58831-1242535262_thumb.jpg post-58831-1242535300_thumb.jpg post-58831-1242535367_thumb.jpg post-58831-1242535582_thumb.jpg post-58831-1242535666_thumb.jpg

Edited by Jezboosted

*evil laffter*

another stag man converting to the darkside! (M35).

way to go Ben, sorry my car isn't still for sale man :P but I'm sure you'll track one down sooner or later.

*evil laffter*

another stag man converting to the darkside! (M35).

way to go Ben, sorry my car isn't still for sale man :P but I'm sure you'll track one down sooner or later.

Thanks Stephen,

I have someone working on it for me! hope to source one from japan... C'mon Aussie Dollar! you can do it!

Here is my baby!

just put it up for sale as I am going M35! let me know if you have a nice one for sale!

Link to sale: http://www.skylinesaustralia.com/forums/Ni...97-t270721.html

Pics:

_bi_6883.jpg

_bi_6899.jpg

_bi_6892.jpg

Excellent pics...I can see you are a pro photographer loved the use of the afternoon light :devil::P and the one with the fish eye...envy the condition of your car ,looks like new...

IMHO C34 > M35

I think it's really personal taste, the M35 is really nice to drive and very luxurious.

I'm sure the C34 is alright too but something that little bit newer really appealed to me.

To each their own, they are both fantastic member's of the stagea family.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...