Jump to content
SAU Community

Car Got Stuck On 9000 Revs Without Me Doing It

RB20_ZED

By RB20_ZED,
in General Maintenance

 Share

Recommended Posts

RB20_ZED Collaborator

RB20_ZED

Posted
Posted

To cut a long story short. Was driving today and the car seemed to accelerate without me making it. I pushed the clutch and pulled it into neutral and the engine reved quickly up to 9000 by itself and stayed there until i was able to cut the power to the fuel pump (luckily i have a kill switch). Im guessing that the accelerator cable got stuck but it seems fine and im worried that it could be caused by something else - maybe turbo/boosting related? I wasn't driving the car hard at all when it happened.

what would cause the engine to spike to 9000 revs and stay there? besides the accelerator cable/pedal getting caught or stuck.

my car seems fine now but im scared to drive it without knowing what may have caused it since the cable doesnt seem like it had anything to get caught on.

any help/opinions would be appreciated.

Al Grand Master

Al

Posted
Posted

The only thing that could cause the engine to rev is jammed accelerator cable or jammed throttle body.

Make sure the cable is not frayed, or does not have resistive tendancies as you let go of the peddle (maybe frayed within the insulation conduate). Best to have a mate inside the car pressing acc on/off and you looking in engine bay. Make sure that nothing is obstructing or can obstruct the cable and throttle body. Remove the inlet pipe and cable from the throttle body, insure the shutter moves freely and smoothly. Ensure that all screws, fittings, etc are tight. Check that the return spring is operating correctly and in a fast manner.

May help to post pics of your throttle body and cable, from various angles (top, sides, front, back, etc.)

cowie165 Veteran

cowie165

Posted
Posted

Great post Al.

Last year I bought a Mazda 626 quite cheaply because the owner (rich guy in Mosman) was worried about an 'engine surge' that caused the motor to rev out to redline with >3/4 throttle. With the bonnet open, it was immediately apparent that a rubber hose was interfering with the throttle cable and holding it open for a few second until friction let the cable slide off the rubber...

He didn't care - he'd already bought a new Volvo 4WD to replace it! :)

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted

i say also check your bac valve.....i have had some cars that do a similar thing but not to the extent of 9000rpms....also to kill the engine i say pull out an efi relay or yank off the crank angle sensor wire.....i cant see hydraulic lock from pulling out spark as unburnt fuel will just be forced out the exhaust valve on exhaust stroke....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Shoota_77
      Car Rotisserie

      By Shoota_77 · Posted

      Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      While it is a very nice idea to put card style AFMs into the charge pipe (post intercooler, obviously), the position of the AFM and the recirc valve relative to each other starts to become something that you really have to consider. The situation: The stock AFM is located upstream the turbo, and the recirc valve return is located between the AFM and the turbo inlet, aimed at the turbo inlet, so that it flows away from and not through the AFM. Thus, once metered air is not metered again, neither flowing forwards, or backwards, when vented out of the charge pipe. When you put the AFM between the turbo outlet and the TB, there is a volume of pressurised charge pipe upstream of the AFM and there is a volume of pressurised pipe downstream of the AFM. When the recirc valve opens and vents the charge pipe, air is going to flow from both ends of the charge pipe towards the recirc valve. If the recirc valve is in the stock location, then the section between it and the TB doesn't really matter here - you're not going to try to put the AFM in that piece of pipe. But the AFM will likely be somewhere between the intercooler and the recirc valve, So the entire charge pipe volume from that position (upstream of the AFM, back through the intercooler, to the turbo outlet) is going to flow through the AFM, get registered as combustion air, cause the ECU to fuel for it, but get dumped out of the recirc valve and you will end up with a typical BOV related rich spike. So ideally you want to put the AFM as close to the TB as possible (so, just upstream of the crossover pipe, assuming that the stock crossover is still in use, or, just before the TB if an FFP is being used) and locate the recirc valve at the turbo outlet. Recirc valve at the turbo outlet is the new normal for things like EFRs anyway. In the even of a recirc valve opening dumping all the air in the charge pipe, pretty much all of it is going to go backwards, from the TB to the recirc valve near the turbo outlet. But only a small portion of it (that between the TB and the AFM) will pass through the AFM, and it will pass through going backwards. The card style AFMs are somewhat more immune to reading flow that passes through them in reverse than older AFMs are, so you should absolutely minimise the rich pulse behaviour associated with the unavoidable outcome of having both a recirc valve and an AFM in the charge pipe.
    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Yep, in my case as soon as I started hearing weird noises I backed off the tension until it sounded normal again. Delicate balance between enough tension to avoid that cold start slip and too much damaging things.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      nvm this comment
×
×
  • Create New...