Jump to content
SAU Community

Recommended Posts

To cut a long story short. Was driving today and the car seemed to accelerate without me making it. I pushed the clutch and pulled it into neutral and the engine reved quickly up to 9000 by itself and stayed there until i was able to cut the power to the fuel pump (luckily i have a kill switch). Im guessing that the accelerator cable got stuck but it seems fine and im worried that it could be caused by something else - maybe turbo/boosting related? I wasn't driving the car hard at all when it happened.

what would cause the engine to spike to 9000 revs and stay there? besides the accelerator cable/pedal getting caught or stuck.

my car seems fine now but im scared to drive it without knowing what may have caused it since the cable doesnt seem like it had anything to get caught on.

any help/opinions would be appreciated.

The only thing that could cause the engine to rev is jammed accelerator cable or jammed throttle body.

Make sure the cable is not frayed, or does not have resistive tendancies as you let go of the peddle (maybe frayed within the insulation conduate). Best to have a mate inside the car pressing acc on/off and you looking in engine bay. Make sure that nothing is obstructing or can obstruct the cable and throttle body. Remove the inlet pipe and cable from the throttle body, insure the shutter moves freely and smoothly. Ensure that all screws, fittings, etc are tight. Check that the return spring is operating correctly and in a fast manner.

May help to post pics of your throttle body and cable, from various angles (top, sides, front, back, etc.)

Great post Al.

Last year I bought a Mazda 626 quite cheaply because the owner (rich guy in Mosman) was worried about an 'engine surge' that caused the motor to rev out to redline with >3/4 throttle. With the bonnet open, it was immediately apparent that a rubber hose was interfering with the throttle cable and holding it open for a few second until friction let the cable slide off the rubber...

He didn't care - he'd already bought a new Volvo 4WD to replace it! :)

i say also check your bac valve.....i have had some cars that do a similar thing but not to the extent of 9000rpms....also to kill the engine i say pull out an efi relay or yank off the crank angle sensor wire.....i cant see hydraulic lock from pulling out spark as unburnt fuel will just be forced out the exhaust valve on exhaust stroke....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey, it's a GT-R, it's just as significant a moment as mine😁 It's not ideal when things are uncertain; I'm the type of person that always has a set plan for things in life so being unsure of this plan puts me in a weird place mentally.
    • Hows your intake piping? Are you still running stock? Having in the stock AFM position would mean, if the BOV was shut/venting out, it'd create the almost stalling kind of effect right // "the rich pulse behaviour" due to MAF thinking air is flowing ? But this would be better than having the bov in the stock position + MAF on/just before cross over piping right?
    • Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card style AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had no flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
×
×
  • Create New...