Jump to content
SAU Community

Recommended Posts

anyway, had my stagea for a few weeks now . and ive been wondering what the hell does this button do thats to the right of the stearing coloum ,

hopeing some one might have a idear :huh:

picture attached :D

`josh

OK

Q: have you got spotlights?

I have the same switch - it switches between the yellow standard fog lights and aftermarket front spot lights.

So, I turn on my headlights with the stalk, then I turn on the yellow fog lights with the same stalk, and then I press that button to switch between yellow fog lights and bright white spotties.

:angry:

FYI:

14|07|00 <BelGarion> dont drag me into it! lol

14|07|04 <BelGarion> i dont wanna look stupid

it was his idear too.

btw i only have the 1 set of foggys next to the lights. soo mabye its defunked on mine.

yet i can hear a relay tripping when i hit it *shrugs*

oh well now i know !

`josh

Edited by avalonea
FYI:

14|07|00 <BelGarion> dont drag me into it! lol

14|07|04 <BelGarion> i dont wanna look stupid

it was his idear too.

btw i only have the 1 set of foggys next to the lights. soo mabye its defunked on mine.

yet i can hear a relay tripping when i hit it *shrugs*

oh well now i know !

`josh

Ive got these:

DCAM0010.jpg

so, got the option of soft yellow lighting, or big kick-arsed bright white spotlights - they are really good!

it depends on the options your car came with as to what that button does. mine has a 'luggage fan' in the boot, which does sfa in my opinion. some stageas were fitted with heated wipers. this is to prevent the wiper blades tearing off when the windscreen is covered in ice.

The real reason they put in a luggage fan is to dissipate the foul odours of the Socks of the Japanese Soccer Team after they have been soundly thrashed by the OZ Rocker Soccerooooooooooooooooooooooooooooooooooooos.

under the spare wheel cover is a plastik sheet with unicorny motifs on it..

when changing smelly socks plasick sheet is lade out so foot odrour's don't not kill the grass..

next model Stagea will have built in foot spare insted of stuipid lil spaer wheel

Edited by 66yostagea

I've got a working luggage fan, hours of fun. The other side has the factory stacker, whats wrong with that? Do others have a 'light reduce' switch? It makes the headlights dim when you're not moving. How does the 'Power' button down by the auto stick work? I notice sometimes when you accelerate hard, but the power button is off, the light illuminates on the button. Pretty confusing.

And up on the dash, the button showing all four wheels with a 'C' in the middle, obviously some sorta diff lock, but what locking exactly?

anyway, had my stagea for a few weeks now . and ive been wondering what the hell does this button do thats to the right of the stearing coloum ,

hopeing some one might have a idear :D

picture attached :)

`josh

Its the Heated Side Mirrors bro! Try it out when they're fogged up, it clears a square in the middle!! :P Wondered who else had that.

It seams this button is majic .

If some one else says it operates the oo7 ejecter seat ill be cross :D

`josh

Haha, no I'm right! I don't know if you've got foggy mirror probs in Oz but in NZ, its rampant. And that button can magically clear them..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...