Jump to content
SAU Community

Recommended Posts

Got all the parts ready to order, just been advised by a mechanic friend to check that the starter motor and shafts don't need changing. Not seen them mentioned here so I assume not?

Nope just use what you have,

  • 3 months later...
  • 2 weeks later...
  • 9 months later...

bringing back an old thread hoping for some help

Has anyone done a manual conversion on a S2? alot of the info in this thread is for series 1 stagea and wiring for the transmission is different from S1 to S2 (tiptronic)

I am assuming the same mod needs to be done for the park inhibiter switch - bridging terminals of the two pin connector, but has anyone sorted out reverse switch wiring? transmission side that is, it appears if you are using the auto harness for the manual - it will need to be cut.

I have a series 2 gearbox which has 2 switches on the side, one for reverse and the other I am not sure so if someone knows which is which that would be great too.

I did do a continuity (resistance) check of the two switches hoping to find out which one had continuity when in reverse gear, but no resistance - could be a faulty switch?

Also, under the centre console there is a little black box - deceleration sensor, it needs to be removed/disconnected to allow the console to fit correctly as it is directly beneath the coin box compartment, has anyone removed this completely or just repositioned it? Has anyone with a factory manual have this little black box? refer to picture

Any help is greatly appreciated.

Jarrad.

post-34938-0-21223500-1398250683_thumb.jpg

sorry I can't help with the auto wiring; but I am pretty sure the black box replaces the earlier gold box as the 4wd sensor (pic is bad, but I think that's it). If so you need to keep it, but reposition it anywhere else available under the console that is flat/level....min is right towards the back of the console

  • 5 months later...

hi,

im thinking of converting my s2 to manual

few questions though.

will an r32 gtr front prop shaft work?or do i need an r33 one?

is there anything else that i need other than whats listed

33 gtst clutch pedal
r33 gtst clutch master cylinder
r33 gtst handbrake
r32 gtr gearbox a push type
r32 gtr clutch and flywheel
r32 gtr clutch slave cylinder
rb25 manual flywheel bolts
rb25 manual spigot bush for the crank
conceptua braided clutch line
manual gearbox bolts

hi,

im thinking of converting my s2 to manual

few questions though.

will an r32 gtr front prop shaft work?or do i need an r33 one?

is there anything else that i need other than whats listed

33 gtst clutch pedal

r33 gtst clutch master cylinder

r33 gtst handbrake

r32 gtr gearbox a push type

r32 gtr clutch and flywheel

r32 gtr clutch slave cylinder

rb25 manual flywheel bolts

rb25 manual spigot bush for the crank

conceptua braided clutch line

manual gearbox bolts

You can just use the front prop shaft from your auto they are all the same. You may have to do something about your speedo drive.

You can just use the front prop shaft from your auto they are all the same. You may have to do something about your speedo drive.

anyone know how to wire the gearbox up in the s2?

what have people done with the speedo drive in the past?

If you don't get a reply just google "electronic speedometer drive for R32 gearbox" or something like that .

As for wiring apart from the speed signal which is obvious there is just the reverse light which you should be able to work out with a multimeter and don't forget the handbrake warning light.

  • Like 1

Hi Jason, I'm not sure exactly what you have found or need, but the later model (33,34) and even Navara electric speedo senders physically fit the 32 gearbox and can be used in the conversion

Hi Jason, I'm not sure exactly what you have found or need, but the later model (33,34) and even Navara electric speedo senders physically fit the 32 gearbox and can be used in the conversion

ok thanks,im not 100% sure myself.

i was under the impression it wasnt a straight swap over?

if the 33,34 senders fit the gearbox ill just pick one of them up.

i just started collecting parts for the conversion.i want to have all the right bits before i start.

looking for part numbers for the following
rb25det flywheel bolts is it (12315-42L11)
rb25det manual spigot bush
rb25det manual gearbox bolts is it (01121-05121 x 3 long top bell housing
31377-15U00 x 3 bottom bell housing
31377-15U01 x 1 bottom bell housing, far left facing the front of the trans, outer bolt for the gusset support.
08911-2101A x 1 hex nut for the far left bolt.)
r33 gtst handbrake cables
thanks

  • 3 months later...

hope someone can help me out here, just did my manual conversion over the last few days, all in ready to turn the key. now i havent yet wired up the reverse lights so hoping that isnt my problem, but i hit the key for the first time tonight and all that happened was the starter motor clicked, car didnt turn over or start.

i have looped the inhibitor switch plug.

also wondering what i do with all the left over wiring that was off the auto box.

the only thing i have running to the box is the speedo plug thats connected.

cheers

battery was fine and charged. some previous owner made the main starter wire black just like the earth wires, naturally i earthed it to body. banged it on positive and all systems go.

cheers everyone on here for there input. helped out a lot with the conversion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
    • Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p
×
×
  • Create New...