Jump to content
SAU Community

Stripped Wheel Studs On My R33

Bunta

By Bunta,
in Queensland

 Share

Recommended Posts

Bunta Grand Master

Bunta

Posted
Posted

Fate has forced my hand! The R32 just blew its turbo so R33 wheel studs need to be fixed so I can drive it while the R32 gets its upgrades done!

Does anyone have any useful advice for me on how to do this?? Or does anyone want to come and help me do it on Saturday afternoon? Rewards of course will be offered for the helpers :D Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/125048-stripped-wheel-studs-on-my-r33/
Share on other sites
AzzurrA Grand Master

AzzurrA

Posted
Posted

1. Take wheel off

2. Take caliper off disc

3. take disc off

4. get big hammer

5. belt old stud out

6. slide new stud in from behind

7. use old stripped stud as a punch to push new stud in (or alternatively get a rattle gun and do up a wheel nut onto the new stud to pull it through)

8. put disc back on

9. put caliper back on disc

10. put wheel back on

11. ????

12. Profit

Eug Grand Master

Eug

Posted
Posted
Where do I buy the new studs from??

Jason there is alcoholic rewards if you come help me :D

try repco they will normally have a range of wheel studs...

i got mine from option1garage over @ hamilton (although i have slightly longer ones 70mm i think)

make sure you get ones with the correct spline, as you'll have a mission of a time bashing them in, or drilling bigger holes etc...

the rattle gun method Azzura mentioned is good, just make sure you dont over tighten and end up ruining your thread as a fair bit of heat is generated. a rubber mallet is also handy - dont know when i used it but i know i used it heaps. after you've replaced the studs remember to periodically tighten up your bolt nuts as they settle in.

not a big job, just time consuming ;)

good luck

Primordial Grand Master

Primordial

Posted
Posted
try repco they will normally have a range of wheel studs...

i got mine from option1garage over @ hamilton (although i have slightly longer ones 70mm i think)

make sure you get ones with the correct spline, as you'll have a mission of a time bashing them in, or drilling bigger holes etc...

the rattle gun method Azzura mentioned is good, just make sure you dont over tighten and end up ruining your thread as a fair bit of heat is generated. a rubber mallet is also handy - dont know when i used it but i know i used it heaps. after you've replaced the studs remember to periodically tighten up your bolt nuts as they settle in.

not a big job, just time consuming ;)

good luck

Yeah don't try to put a front stud in the rear hub, and waste two hours of your time before you realise that they are actually different!!! Like I did at the track day!! :D

Studs are only about $5 each... Once you know how its pretty easy - like anything I guess.

You dont HAVE to use a rattle gun, but it makes it much easier.. You will have to pack the wheels stud up with washers or a big nut so that you can wind the nut onto the stud without running out of thread on the nut. I hope that makes sense?

AzzurrA Grand Master

AzzurrA

Posted
Posted

i'm happy to help out Andy.

I got my wheel stud from Nissan, as they are the same as R32 GTR ones.

was cheap as chips... think it was like $7 or something

don't know if they'd have R33 ones though, or if they're the same etc (though one would assume they would be?)

impact_blue Grand Master

impact_blue

Posted
Posted
Yeah don't try to put a front stud in the rear hub, and waste two hours of your time before you realise that they are actually different!!! Like I did at the track day!! :D

Oh dears! I was wondering what you were gonna do! I felt so bad for ya too, you were having an awesome run!

Bunta Grand Master

Bunta

Posted
  • Author
Posted
Hey Andy,

You got my number, gimmie a call if you need a hand. I am but 5 mins from your house.

Thanks mate ;)

Yeah don't try to put a front stud in the rear hub, and waste two hours of your time before you realise that they are actually different!!! Like I did at the track day!! :D

Studs are only about $5 each... Once you know how its pretty easy - like anything I guess.

You dont HAVE to use a rattle gun, but it makes it much easier.. You will have to pack the wheels stud up with washers or a big nut so that you can wind the nut onto the stud without running out of thread on the nut. I hope that makes sense?

I should have watched you fix that!! By the way....Watching your car on the track got my mouth watering, gave me a preview of my engines future :)

i'm happy to help out Andy.

I got my wheel stud from Nissan, as they are the same as R32 GTR ones.

was cheap as chips... think it was like $7 or something

don't know if they'd have R33 ones though, or if they're the same etc (though one would assume they would be?)

Thanks mate! ill give you a call later in the week??

Primordial Grand Master

Primordial

Posted
Posted
I should have watched you fix that!! By the way....Watching your car on the track got my mouth watering, gave me a preview of my engines future :D

Hehe yeah, if only you were psychic and knew you were going to need to know how to do it! ;)

I can promise that you wont be disappointed with the turbo! :)

Bunta Grand Master

Bunta

Posted
  • Author
Posted
Hehe yeah, if only you were psychic and knew you were going to need to know how to do it! :D

I can promise that you wont be disappointed with the turbo! ;)

I knew at the time that it needed doing...I just didnt know that is what you were up too!!!!

we can have "comparisons" at EC in October Woooooot

WiZardOz Collaborator

WiZardOz

Posted
Posted

if you need to know details of the studs that are required check out the www.niceproducts.com.au website - all the info you need is there

I am having mine replaced, but the biggest problem has been finding wheel nuts to suit my mags ..

A workshop told me it's only a 20 minute job to preplace all studs to both rear wheels .. sounds like the easy option to me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...