Jump to content
SAU Community

Series 2 R33 Parts Calipers $270 Rotors $80


Recommended Posts

Front Calipers $270

calipersd4.jpgbrakesrw3.jpg

Front Rotors $80 or $50 with the calipers

Digital Climate Control SOLD

climatezf2.jpg

Front Hub/ Axle Assy's $ 20 for both

axleslc7.jpg

Rear Bumper $30

Stock Rear Spoiler with brakelight $30

Rear Pod 1 only SOLD

R33 Nissan Rear boot lip SOLD

lipaf1.jpglip1nz7.jpg

LH Lower Control Arm SOLD- payed for and sent

LH Upper Control Arm SOLD-payed for and sent

upperarmng2.jpg

LH Radius Rod SOLD- payed for and sent

radiusib1.jpg

Clutch Master Cylinder $15

Black Plastic Under Guard & both for under fenders $15 the lot SOLD

undercarguardqb1.jpg

Boot Trim Piece SOLD

bootpieceqn3.jpg

Front Sway Bar $20

swaymr9.jpg

Air Flow Meter RB25DET SOLD - payed for and sent

afmbj6.jpg

1 x 245/45/16 Bridgestone tyre $20

tyrevy0.jpg

S13 Seats $90

s13seatsai9.jpg

Silvia Fuel Pump $30

silviapumpau6.jpg

All body parts are Black.

I can send anything anywhere, but I am in Adelaide if you want to pick anything up.

Cheers

Edited by ForcedRex7
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Have you adjusted the clutch pedal rod? You can wind it in to shorten it. Just can be a cnut to get to.
    • Yes sir, that was me. Fake ARP's are also a thing over here in Canada and we only order from reputable dealers. It's sad that even simple things like bolts and hoses are now also being copied... anything to make a dollar.  Story time. Like all cheap crap from China, it's even an issue with firearms. Roughly 15 years ago, I purchased a new cheap Norinco 12g shotgun. First time out in the bush with it, while firing, bolt assembly didn't lock and it fired out of battery. The receiver also being cheap steel, basically exploded in my face. I was lucky to be wearing eye protection. Long story short, don't buy Chinese junk. Also Norinco being state run and their only military arms producer, if ever they do try and take over a country, don't worry about it lol. 
    • Installed  Nismo coppermix twin competition spec last year in my bnr32 with pull trans with Oem slave cylinder. The point at where the clutch disengages/enages is right at the top of the clutch pedal, meaning I barely have to push the pedal down for the clutch to be disengaged.  You guys that have the same combo are you experiencing this high pedal bite point??   Secondly I’d like to have the disengagement point lower meaning I have to push the pedal more(further not effort)for it to be disengaged.  I’m thinking to use a Nismo big operating cylinder(bigger bore at 13/16 vs Oem 3/4) which will require more pedal stroke to get the equivalent movement at the clutch fork. But I see Nismo web site says not to mix these 2 as the Nismo big operating cylinder doesn’t have enough stroke to disengage??? Any folks run both the coppermix twin pull with Nismo cylinder??    Thanks in advance for the replies but prefer only guys with pull clutches to respond. thanks     
    • Any chance u could let us know where your based ?
×
×
  • Create New...