Jump to content
SAU Community

Recommended Posts

Hi Guys,

Just hoping someone can point me in the right direction.

I've got a 96 R33 GTST with K&N Pod, 3" Zorst, BOV and FMIC with boost around 11-12psi (done by a Turbosmart manual bleeder value).

When i go to accelerate (overtaking on the highway) you can hear the pod filter etc going crazy sucking in air but the car doesnt really take off (it used too and it isnt just that i'm used to the car.. i've had it for 2 years and i know somethings wrong). It will take off but struggles and it surges and then hits flat spots and then surges again all the way up the rev range. Seems like something is holding it back.

I do have dud coils but i have taped them with electrical tape and they seem to be ok for a $10 fix (they are really bad without taping).

I have cleaned my AFM once before when i had a very similiar situation and it seemed to have resolved the problem but i dont want to keep getting this problem. I've only driven the car about 2000kms in the last 6mths (also since i cleaned and re-oiled the filter).

Also when travelling on the highway and going to over take (whether in 4th or 5th gear), if i just hammer it, my car cuts out (like the fuel-cut comming in) but if i slowly climb there is no cut out.

If anyone can suggest where i should look at, i'd appreciate. thanks

well the cut out in 5th gear is rich and retard mode. only way to get rid of that is either new ecu or wind the boost down.

how old are your spark plugs? and what type? that could be part of the problem.

Hi,

Thanks for the replies.. Just wondering why when i overtake i 4th or 5th and i slowly put the pedal down it doesnt cut out but when i plant it, the fuel cut comes in... could this be because of a bad bleeder/boost value?

Also, i havent changed my sparkies in a while so maybe i will this weekend and i'll gap them.

Anyways, thanks guys again.

wouldnt think the boost controller would have anything to do with the problem. It will just be fuel cut coming in...R&R as stated before, a/m ecu will fix it. Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change.

Yer im in a similar situation dude, with the same b/c as urself.....try winding it back a touch....

Originally posted by r33 racer

Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change

Exactly wat i thought! :laugh:

the way that r&r works isn't by boost pressure. it isn't just a case of once it reaches a certain pressure it cuts out. that is why it won't do it if you ease the throttle on.

but yes the cold weather has an effect on it. just wind the boost down a bit.

its based on a ramp scale. i started a thread about this to find out exactly.

what happens is that the ecu has a set maximum airflow per rpm. so if it exceeds that amount it cuts out.

for example, the airflow at 14psi might be within limits at 6000rpm, but not at 3000rpm, so it cuts out. i will draw a graph to illustrate it when i get time.

haha no...i dont think so...try winding the boost down and see how it goes mate. Take things one step at a time...you never do 5 things to fix one problem or you will never know what fixed it.

Thats also an idea below...try some contact cleaner through your afm.

Edited by r33_racer

I didnt notice this problem until last weekend when i went for a long drive and needed to overtake. But the period after re-oiling, i didnt have any problems.

And yes i would love to buy new coil packs but i dont have the money yet.

Well, i'll wind the boost down first and get new sparkies and have em gapped.

Then i'll see how it goes.. I'll clean the AFM anyway.

Thanks guys.. will keep you posted.

Could be a number of things (as usual) but coil packs usually fluctuate when faulty under load which is what you are experiencing when trying to overtake. Which also explains, that when you decrease the amount of boost you are running that the problem will go away.

Theres plenty of advice throughout these forums to detect faulty coil packs.

Hi All,

I've changed my plugs with NGK BCPR6ES (i think that's it) which are standard gapped to 0.8mm and wound down the boost to run 10 or 10.5 (needle on boost gauge is half between 10 and 11). The 33 seems to run quite well.

However saying that, the old plugs didnt look to bad either but who cares when the car is running much better.

thanks alot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey, it's me! Though honestly, if I had 20M in my bank account tomorrow, I would not want to be rid of my car all of the sudden - Which makes me think this is money stuff, not "I actually hate car" stuff. I'd probably double down and buy even more trinkets and fun things for it. If this is not you, then sell it cheaper. It will sell at a certain price after all.
    • This is the LCA mount reloctaion kit. Self explanatory in its description. https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=62&_fid=1e812d392&_ss=c These are the alloy subframe bush inserts that I am using. I like them. https://au.gktech.com/products/rear-subframe-slip-in-collars?_pos=29&_fid=1e812d392&_ss=c Alternatively, if you have original and shitty bushes, you might consider outright replacement with poly. https://au.gktech.com/products/polyurethane-rear-subframe-bushes?_pos=28&_fid=1e812d392&_ss=c I would also higly recommend that you look into adjustable RUCAs and tension rods, so you can sort out the camber and bump steer behaviour, especially if the car will be any more than ~15mm lower than stock. I would also highly recommend the GKTech FUCAs, although you really should do some research and learning on the subjetc of R32 FUCAs before making any decisions. All of this will be criticaly difficult to get through a TÜV inspection too, if that happens to be relevant to you. Note that if you do install the relocation kit, you will absolutely have to replace the associated bushes with spherical joints (you can read all about that on the product page) or upgrade the LCAs also.
    • I picked up my block and head last week and have been slowly assembling it since then. Pictures I took earlier this week. The rest of the auxiliaries are on now. I just have my intake manifold runners to tap for my WMI direct port setup before putting it back on. I should hopefully have the motor back in by this weekend.   
×
×
  • Create New...