Jump to content
SAU Community

Recommended Posts

Hi Guys,

Just hoping someone can point me in the right direction.

I've got a 96 R33 GTST with K&N Pod, 3" Zorst, BOV and FMIC with boost around 11-12psi (done by a Turbosmart manual bleeder value).

When i go to accelerate (overtaking on the highway) you can hear the pod filter etc going crazy sucking in air but the car doesnt really take off (it used too and it isnt just that i'm used to the car.. i've had it for 2 years and i know somethings wrong). It will take off but struggles and it surges and then hits flat spots and then surges again all the way up the rev range. Seems like something is holding it back.

I do have dud coils but i have taped them with electrical tape and they seem to be ok for a $10 fix (they are really bad without taping).

I have cleaned my AFM once before when i had a very similiar situation and it seemed to have resolved the problem but i dont want to keep getting this problem. I've only driven the car about 2000kms in the last 6mths (also since i cleaned and re-oiled the filter).

Also when travelling on the highway and going to over take (whether in 4th or 5th gear), if i just hammer it, my car cuts out (like the fuel-cut comming in) but if i slowly climb there is no cut out.

If anyone can suggest where i should look at, i'd appreciate. thanks

well the cut out in 5th gear is rich and retard mode. only way to get rid of that is either new ecu or wind the boost down.

how old are your spark plugs? and what type? that could be part of the problem.

Hi,

Thanks for the replies.. Just wondering why when i overtake i 4th or 5th and i slowly put the pedal down it doesnt cut out but when i plant it, the fuel cut comes in... could this be because of a bad bleeder/boost value?

Also, i havent changed my sparkies in a while so maybe i will this weekend and i'll gap them.

Anyways, thanks guys again.

wouldnt think the boost controller would have anything to do with the problem. It will just be fuel cut coming in...R&R as stated before, a/m ecu will fix it. Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change.

Yer im in a similar situation dude, with the same b/c as urself.....try winding it back a touch....

Originally posted by r33 racer

Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change

Exactly wat i thought! :laugh:

the way that r&r works isn't by boost pressure. it isn't just a case of once it reaches a certain pressure it cuts out. that is why it won't do it if you ease the throttle on.

but yes the cold weather has an effect on it. just wind the boost down a bit.

its based on a ramp scale. i started a thread about this to find out exactly.

what happens is that the ecu has a set maximum airflow per rpm. so if it exceeds that amount it cuts out.

for example, the airflow at 14psi might be within limits at 6000rpm, but not at 3000rpm, so it cuts out. i will draw a graph to illustrate it when i get time.

haha no...i dont think so...try winding the boost down and see how it goes mate. Take things one step at a time...you never do 5 things to fix one problem or you will never know what fixed it.

Thats also an idea below...try some contact cleaner through your afm.

Edited by r33_racer

I didnt notice this problem until last weekend when i went for a long drive and needed to overtake. But the period after re-oiling, i didnt have any problems.

And yes i would love to buy new coil packs but i dont have the money yet.

Well, i'll wind the boost down first and get new sparkies and have em gapped.

Then i'll see how it goes.. I'll clean the AFM anyway.

Thanks guys.. will keep you posted.

Could be a number of things (as usual) but coil packs usually fluctuate when faulty under load which is what you are experiencing when trying to overtake. Which also explains, that when you decrease the amount of boost you are running that the problem will go away.

Theres plenty of advice throughout these forums to detect faulty coil packs.

Hi All,

I've changed my plugs with NGK BCPR6ES (i think that's it) which are standard gapped to 0.8mm and wound down the boost to run 10 or 10.5 (needle on boost gauge is half between 10 and 11). The 33 seems to run quite well.

However saying that, the old plugs didnt look to bad either but who cares when the car is running much better.

thanks alot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
    • I have a r34 sedan 1999 manual converted need some help with my speedometer it only reads upto 98km and then stops currently still running the auto cluster any easy fixes no speedo drive is connected yet, if someone has a video for wiring up the manual speedo sensor with the auto cluster please send through 
×
×
  • Create New...