Jump to content
SAU Community

Recommended Posts

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

increased fuel consumption, also using a 1GZE SC is like using a stock trubocharger off a GTSt. Unless u go for a $6000 vortech/eaton centrifugal supercharger (which is like puttin a T88 on ya GTSt) you'll never get optimal results out of a supercharger.

The reason Nissan never came out with em is that in small capacity cars (3.0L and under) its not completely efficient.

if u do consider supercharge

the car will be be more like a 4.0L aussie six

plenty of torque and power, but power wont peak that high in the rev range as our cars currently do.

u can get SC that can rev and stay someone efficient at the higher revs, but it also cost money

not necessarily, those are the oldschool superchargers that work better at higher revs.

If you look at the boost charts, the turbo charger has an exponential boost (very low boost for initial phase and very high boost after the sweet spot). A supercharger however is belt driven, ie constant. It has a linear looking chart, therefore you'd have better midrange boost than a turbo, and much better pickup at the lower end. You do however have to tune it so you don't overboost at higher revs.

eg: say hypothetically your max boost is 14psi

REVS.-> 0 . 1000 ..2000 . 3000 . 4000 . 5000 . 6000 . 7000

SC.....-> 0 ... 1 ...... 4 ...... 6 ...... 8 ..... 10 .... 12 .... 14

TURB.-> 0 ... 0.5 .... 1 ...... 2 ...... 4 ...... 8 ..... 11 .... 14

however true linearity is only achieved by centrifugal superchargers (I think, not sure) and thems the more expensive ones.

Oh and as for the q about the ECU having to be modded... NFI, I gave up and decided to go for a GTR b4 I could investigate it.

there are companies which specialise in superchargers. go through your yellow pages and find one and given them a call and have a chat about your options. i'm sure they will let you know all that you have to do.

SC can't be too bad of an idea if mercedes chooses them over turbo's. also many american professional drag cars use superchargers because of their low-down torque and power.

would be great to see a SC skyline zoom past any gtst and do well against a gtr!

u gotta spend sum serious cash for that. The company I wastaling to was adelaide based, and they specialised in supercharging civics and the like, so I gave em a buzz... think they were working on a supra at the time, either doin a super/turbo twinny or a straight super, sumfin liek that, they were the ones that gave me quotes for manifold fabrication n stuff.

I got their email at home, I'll post it when i get back from work

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah the ACL and similar formable heat shielding materials are really nice. But most people do not have the patience or talent to do a good job like that. Almost anything is better than nothing though. Even if you didn't form it closely like that and just had a slab of it slipped in between the manifold and somewhere/thing you wanted to protect, you would gain benefit. There has to be a market opportunity for people like Artec to make formed heatshields to suit their cast manifolds. The fact that they are cast means that they are consistently the exact same dimensions and they could add bosses to the castings like you see on stockers to allow heat shields to be firmly attached yet floating away from the manifold itself.
    • I've seen some stuff like this as well, not sure if it's a good idea or anything but it does have more standoff from the piping than the conventional fiberglass wrap:  
    • Jap premium will be 100 RON. You should use 98.
    • The exhaust gases are at their highest temperature as they leave the exhaust port and enter the manifold. They cool as they flow through the manifold because they transfer heat to the manifold and the manifold loses heat to the surrounding environment. Thus, inevitably, the exhaust gases are cooler as they enter the turbo compared to when they entered the exhaust manifold. So, yes, the exhaust manifold can easily get as hot as the turbine housing. Having said that, you will generally see the highest temperatures where the exhaust gases have to slow down or they are concentrated into one area - which is usually the collector on the manifold and in the turbine housing, because the gases slam into the metal at those places, increasing the convective heat transfer coefficient and transferring even more heat to the metal than they might just flowing past elsewhere. Exhaust manifold heat shields are a good idea - certainly for the stock manifold they are there from the factory. People seldom have anything like that on a tubular manifold because they are hard to achieve. Some might wrap a tube manifold with fibreglass tape - but this has a reputation of leading to cracked welds. The best case is generally to put ceramic coating onto the manifold to prevent it getting as hot (internal coating) and radiating/convecting heat into the bay (external coating). All the real heat from a turbo comes from the exhaust side. The gases entering are at ~800-900°C and the steel/iron gets nearly that hot. The compressor side is only going to heat the charge air up to <<200°C (typically not much more than 100°C). So that's nothing, by comparison. The compressor is not a significant source of engine bay heat.
    • Late to the party, specifically joined this forum as I just bought one of these and this thread has been a gold mine of info. If the OP is still around, mind if I ask what gas you been putting in yours? Mine has a Japanese sticker in the cap saying premium but it seems to get way worse mileage on premium (95) than 91. I always thought it was meant to be the other way round🤷 I do think Nissans claimed "6l/100km" is a bit fantastical 😂
×
×
  • Create New...