Jump to content
SAU Community

Recommended Posts

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

increased fuel consumption, also using a 1GZE SC is like using a stock trubocharger off a GTSt. Unless u go for a $6000 vortech/eaton centrifugal supercharger (which is like puttin a T88 on ya GTSt) you'll never get optimal results out of a supercharger.

The reason Nissan never came out with em is that in small capacity cars (3.0L and under) its not completely efficient.

if u do consider supercharge

the car will be be more like a 4.0L aussie six

plenty of torque and power, but power wont peak that high in the rev range as our cars currently do.

u can get SC that can rev and stay someone efficient at the higher revs, but it also cost money

not necessarily, those are the oldschool superchargers that work better at higher revs.

If you look at the boost charts, the turbo charger has an exponential boost (very low boost for initial phase and very high boost after the sweet spot). A supercharger however is belt driven, ie constant. It has a linear looking chart, therefore you'd have better midrange boost than a turbo, and much better pickup at the lower end. You do however have to tune it so you don't overboost at higher revs.

eg: say hypothetically your max boost is 14psi

REVS.-> 0 . 1000 ..2000 . 3000 . 4000 . 5000 . 6000 . 7000

SC.....-> 0 ... 1 ...... 4 ...... 6 ...... 8 ..... 10 .... 12 .... 14

TURB.-> 0 ... 0.5 .... 1 ...... 2 ...... 4 ...... 8 ..... 11 .... 14

however true linearity is only achieved by centrifugal superchargers (I think, not sure) and thems the more expensive ones.

Oh and as for the q about the ECU having to be modded... NFI, I gave up and decided to go for a GTR b4 I could investigate it.

there are companies which specialise in superchargers. go through your yellow pages and find one and given them a call and have a chat about your options. i'm sure they will let you know all that you have to do.

SC can't be too bad of an idea if mercedes chooses them over turbo's. also many american professional drag cars use superchargers because of their low-down torque and power.

would be great to see a SC skyline zoom past any gtst and do well against a gtr!

u gotta spend sum serious cash for that. The company I wastaling to was adelaide based, and they specialised in supercharging civics and the like, so I gave em a buzz... think they were working on a supra at the time, either doin a super/turbo twinny or a straight super, sumfin liek that, they were the ones that gave me quotes for manifold fabrication n stuff.

I got their email at home, I'll post it when i get back from work

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah 98 for me, and 6.7/100 was my actual usage. On the downside the bloody thing still isn't running properly but at least they hybrid system is happy now. It starts but missfires like a bastard, and isn't throwing any code except "missfire". Thanks scoop. I did notice the AFMs are reading quite different at idle 1.33v and 1.67v so 25% variance (and have both changed and swapped them, the issue stays on the driver's side afm) so I'm looking for exhaust restriction (mouse nest?), compression issue or (hopefully not, no physical damage seen) wiring issue. Throttle might also be an issue but that is harder because you can't swap them side to side and not cheap to fire the parts cannon at.
    • I hope you're right and it somehow justifies it's existence!
    • actually, I've had one of those for a while and it gets more use than you'd think. Yes catching subframes, engines etc coming out under a car on a hoist, but also getting heavy stuff on shelving (to a certain height) without a forklift, holding the fuga's hybrid battery....like many good tools you'll find the jobs for it once you have it
    • Right, so God, it's been nearly 12 months since my last confession....  The main confession is I'm a horrible car modifier (amongst other things).  Obviously the pool was a massive distraction for the entirety of last year but really doesn't excuse me for doing nothing at all on the car for this year.  To be honest this year was a mental break to get over the extreme mental torment and pressure I put myself through putting the pool in!  It really was a slog.  The pool is still not completely finished but it might never be....  The kids love it and the wifey and I love it so mission success! I have spent a grand total of 30 minutes working on the car since when I commenced on the pool.  I just have not had a spare brain cell to be able to focus on it.  The thought of working on it just seems abhorrent to be honest.  My heart is just not into it.  Yet..... What I have done is decide that I'm a clown to not paint ALL of the underside of the car while I'm at it.  Originally I was stopping at the start of the rear subframe to then "get back to it later on once I'm ready".  Let's be honest, later on might never happen so may as well keep diving in!  I'm already balls deep so may as well go a bit deeper! So......  I've just purchased a hydraulic scissor lift table to be able to take the rear subframe out as a whole unit without having to dick around with jack stands rolling around on the ground.  Us 6' 8" blokes don't operate well at ground level! One of these- Anyway, will the investment in an expensive tool that I'll probably only ever use for one job motivate me to crack on?  Only time will tell..... Wish me luck!
    • Yeah the ACL and similar formable heat shielding materials are really nice. But most people do not have the patience or talent to do a good job like that. Almost anything is better than nothing though. Even if you didn't form it closely like that and just had a slab of it slipped in between the manifold and somewhere/thing you wanted to protect, you would gain benefit. There has to be a market opportunity for people like Artec to make formed heatshields to suit their cast manifolds. The fact that they are cast means that they are consistently the exact same dimensions and they could add bosses to the castings like you see on stockers to allow heat shields to be firmly attached yet floating away from the manifold itself.
×
×
  • Create New...