Jump to content
SAU Community

Help Needed Epa Test Troubles

NVMYTG

By NVMYTG,
in General Maintenance

 Share

Recommended Posts

NVMYTG Contributor

NVMYTG

Posted
Posted (edited)

my r33 gtst needs to pass an EPA test and to do so i need to have standard boost control parts running. at the moment i have a duel stage boost controller and it runs fine with the duel stage. when i put the vac lines to the standard controller it overboosts. can someone tell me what vac lines need to go where? also i have made sure the plug that comes from the standard controller is plugged in and i have even tried another one from a mates car. could the wiring for the standard controller be used for the aftermarket unit? if so what should i be testing for with the multi meter? the after market controller has an earth wire and a wire running through the firewall and i cant see if the wire from the standard plug has been cut as it dissapears into a loom. any help would be much appreciated. thanks, brad (also my car has a standard turbo,FMIC and at the moment the airbox is fitted and i have checked for vaccum leaks)

Edited by NVMYTG
Link to comment
https://www.sau.com.au/forums/topic/127617-help-needed-epa-test-troubles/
Share on other sites
RANDY Veteran

RANDY

Posted
Posted

You won't need a multimeter... the standard solanoid should give 5psi if it's not working properly, and 7psi if it is.

I suggest that your plumbing is not quite right... from the intake pipe down the bottom, the pipe should come into the bottom of the solanoid (I think.. if not, switch them around), and then the top one goes to your wastegate actuator.

NVMYTG Contributor

NVMYTG

Posted
  • Author
Posted

i treid the lines both ways but i was a little worried id do some damage can anybody confirm which way they are supposed to go? also id like to know what im looking for with a multimeter with the wires coming from the solinoid as i said before i tried the vac lines both ways and i even tried another solinoid from my mates car which i know works.

Mick Mentor

Mick

Posted
Posted

from memory one of the lines was running to a T peice, also one line had a little restrictor in it, if thats not in the right place that may cause your problem.

Let me work out what needs to go where cos im in the exact same boat as you, i have a dual stage boost controller installed and i need to put the standard one back on so i can get it trough RoadWorthy.

Mick Mentor

Mick

Posted
Posted

Ok here is what i worked out on how to properly install the stock boost controller.

First off there is a hose from the actuator goin to a T peice, its only short and it has a yellow band on it because it has a brass restrictor in it.

From the T peice it goes to the BOV retuirn pipe.

Then from the T peice it goes to the bottom of the boost controller.

The last is a straight hose goin from the intercoller pipe to the top of the boost controller.

Can someone please confirm this for me, i just want to be %100 sure.

I mainly want to know if the restrictor is in the short hose coming off the actuator and goin to the T peice.

I hjope this helps, im %99 sure this is right which i would love someone to confirm this all for me ..

mad082 Grand Master

mad082

Posted
Posted (edited)

no thats wrong.

(if you have a front mount there will be a hose from the bov pressure line (the vacuum hose that opens the bov) instead of the intercooler pipe)

there should be hose hose from an intercooler pipe. this goes to a T piece. from the T piece there should be 1 hose going to the wastegate, and 1 to the lower hose of the factory solenoid. the top hose of the solenoid should go back to the intake (bov plumback pipe).

Edited by mad082
Mick Mentor

Mick

Posted
Posted

Ok this is straight from the Nissan Fast program, so thjere is no disputing it.

Top of the boost controller goes straight to the wastegate.

The bottom goes to the T peice.

One side of the T peice goes straight to the intercooler pipe.

The other side of the T peice goes straight to the BOV return plumbing.

Thats it, 100%..

Mick Mentor

Mick

Posted
Posted (edited)

I also found a picture in another thread showing the stock setup i described.

The restrictor is in the short hose goin from the intercooler pipe to the T peice, make sure you have the restrictor in place.

http://www.skylinesaustralia.com/forums/in...st&id=45802

Edited by Mick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Ok glad you clarified on the frenchy’s options , I was worried about if my oem hoses would fit the new compressor or not if I just bought the bracket/compressor kit ,  didn’t realize they also sold a larger full conversion kit. Hmm may just go oem in that case then to make it easy only because I plan to sell this car to upgrade to a 32 GTR or 34 GTT.
    • sausagepianist
      V36 2008 Coupe Wiring Differences with Android Screen

      By sausagepianist · Posted

      Right, here's a video of the basic operation at least.  This is what you can expect day to day when you turn the car on and it boots from standby.  The only thing from a media point of view I haven't gotten working is for it to autoplay plexamp when it turns on from standby (it works from cold boot) but that's more of a plexamp problem as it will autoplay other music players.  Also attached is my one stray cable.  It's part of the screen's wiring adapters but there's just nowhere for it to go in my car.  I've just now done a bit of research and found a matching port on a 2010-2014 head unit with BOSE.  Mine has no BOSE so that's that case pretty much closed I think.  Plugging in the Infiniti AC panel basically did nothing for me, so that's a dead end as well.  Next port of call is to mess with this CANBUS module and see what I can find from it.  I found this resource containing the DBC files for a 2010+ G37 : https://github.com/icecube45/Dash_InfinitiG37/blob/master/InfinitiG37.dbc I'll now have something to go from when I try to extract my CANBUS data so I can see if the HVAC Mode, Fan Speed, Temperature, etc. match and also the gear shifter position.  It's a pretty big assumption that it's just mismatched CAN signals but considering all the devices in the CAN network are talking to each other (AC can be fully adjusted just with no info on screen) it might be a safe one.  I will report back WhatsApp Video 2025-02-26 at 12.49.10.mp4
    • sausagepianist
      V36 2008 Coupe Wiring Differences with Android Screen

      By sausagepianist · Posted

      Thanks for that Paul.  Do you think if I posted a picture you'd be able to remember where it went? 
    • sausagepianist
      V36 2008 Coupe Wiring Differences with Android Screen

      By sausagepianist · Posted

      Sorry Duncan, I didn't get a notification for the replies.  Thanks for responding!  It's a full Android device, but does allow you to use CarPlay/AA as well.  This is the one I bought from NaviRS on AliExpress: https://www.aliexpress.com/item/1005006368602668.html?spm=a2g0o.order_list.order_list_main.111.59aa1802JDzQ0E - the 2K 8G-256G CAM variant but it seems to have gone up by £170 since I bought it!  My purchase was ￡307.14.   It's not the fastest thing in the world but performs perfectly adequately.  It stays on standby unless I disconnect the battery and let it power down, then it's just a fairly standard Android bootup time from cold.  The DSP Equaliser is very nice and made the standard stereo system sound pretty decent compared to the stock screen.  Perhaps I can take a video of it when I get a sec. It *allegedly* supports the reverse camera, but I'm yet to get that working.  It has options for reverse cam (a camera unit can be bought separately) or 360 cameras (also bought separately).  To be fair it doesn't seem to detect that the shifter was put into reverse but I'm working on a theory about this as well.  At the moment I'm going without which is a bit annoying considering the car is an absolute canal barge but so far I haven't caused any damage I'll grab a picture of the wire I'm missing later today when I can get outside.  My theory, by the by, is that not only is the head unit different, but the CANBUS network has different signals for the different years.  I think this because I have a spare AC panel from a newer Infiniti G37 (as opposed to my Nissan panel) which wouldn't control anything except the volume when I had it wired up with the stock system.  I'm going to throw it back in and see if the screen will respond to it.  I've just ordered an arduino CANBUS module so I can have a look at the signals going around the car and see if I can spot anything.  I'm thinking if I can work out what it's expecting vs what it's getting I might be able to translate and relay the signal back but so far just a theory anyway. I also found this on my travels, so far the only one that specifically matches my car: https://www.aliexpress.com/item/1005002822934280.html?spm=a2g0s.imconversation.0.0.33433e5fgttovi If you look at the picture of the before, it has the card reader slot, and the picture of the head unit is exactly the same as the one pictured in my original post.  I asked if they sell the cables separately but sadly they won't.  I didn't want to just buy this one because it's a super old Android version and only dual core - likely slow as hell. 
    • sonicii
      V35 Overheat + Coolant Boil & Overflow + Engine not Starting

      By sonicii · Posted

      As above, you did refill the coolant and burp the system before running it again didn't you?
×
×
  • Create New...