Jump to content
SAU Community

Found An Oil Pot In The Boot Area...

IMPORTD

By IMPORTD,
in Four Door Family & Wagoneers

 Share

Recommended Posts

IMPORTD Grand Master

IMPORTD

Posted
Posted

Just checking out all the different things on the stag, and found an oil pot thingy in the side panel on the right hand side of the boot area. What is it for?

I was trying to find the rear window wash bottle to fill up, still haven't found it lol

Any ideas on both?

Link to comment
https://www.sau.com.au/forums/topic/127637-found-an-oil-pot-in-the-boot-area/
Share on other sites
Ska Grand Master

Ska

Posted
Posted

The bottle in the rear is your ATTESSA system fluid, (for your 4wd) and the rear washer bottle is the same as the front washer, looking at the enginebay from the front, there should be a yellow cap with a long elongated S shape tube, on the left, near the battery, that is the washer fluid container, well the top of it.

Ska Grand Master

Ska

Posted
Posted

I dunno, but it the car hot/cold? I bet if you check it after driving it around for a bit and then stopping that the levels would be fine, as that fluid is compressd when it is used so the level would drop......?

BUT Then again I really wouldnt have a clue eh, just guessing, wait for Alex or Brad or Gary for an answer from a knowlegable source :)

CruiseLiner Mentor

CruiseLiner

Posted
Posted (edited)
Thankyou :happy:

With the ATTESSA Fluid, the level is about 1cm over the max line... this can't be good...??

hey kylie thats normal, u gotta check the fluid level with the car ignition turned on and it will drop to the correct level. its just drained back up abit when ignition is off.

cheers

Brad

Edited by CruiseLiner
  • 2 weeks later...
stasis Mentor

stasis

Posted
Posted

when you guys says its the ATTESA system does it means the transfer case? Cos i want to check every fluid in the car. I dont trust those Kamilaze guys.

First of all the didnt fill the coolant resovoir tanks. Engine oi is fine. Power sterring fluid is over filled i check it when its cold. I want to check the transfer case, gerbox and the diffs. Does it means that i have to jack the whole car up and also the car is so damn low

stasis Mentor

stasis

Posted
Posted
Ah sorry mate, the reservoir in the boot is just for the Attessa pump system, which pressurises the clutch pack in the transfer case. The transfer case oil is separate.

Ok so what kind of oild does it use? Gearbox oil? hydralic oil? or diffs oil?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Duncan
      3D printing fun

      By Duncan · Posted

      Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
    • Duncan
      R32 GTS (RB20DE) clogged cat

      By Duncan · Posted

      I'm not sure what sort of shops are nearby, but I'd expect any reasonable exhaust shop could put a cat in it that will not restrict the power that engine makes. Otherwise, if you want to remove it, short lengths that replace the cat are readily available online, search for "de-cat pipes" or "test pipes"  
    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
×
×
  • Create New...